What is the under lying cause of this problem?()
A. A remote physical layer problem exists.
B. The host NIC is not functioning.
C. TCP/IP has not been correctly installed on the host.
D. A local physical layer problem exists.
您可能感興趣的試卷
你可能感興趣的試題
A.switch to switch
B.switch to hub
C.switch to router
D.hub to hub
E.router to PC
A.The transport layer divides a data stream into segments and may add reliability and flow control information.
B.The data link layer adds physical source and destination addresses and an FCS to the segment.
C.Packets are created when the network layer encapsulates a frame with source and destination host addresses and protocol-related control information.
D.Packets are created when the network layer adds Layer 3 addresses and control information to a segment.
E.The presentation layer translates bits into voltages for transmission across the physical link.
A.802.1Q native VLAN frames are untagged by default.
B.802.1Q trunking ports can also be secure ports.
C.802.1Q trunks can use 10 Mb/s Ethernet interfaces.
D.802.1Q trunks require full-duplex, point-to-point connectivity.
E.802.1Q trunks should have native VLANs that are the same at both ends.
A.it is a layer 2 messaging protocol which maintains vlan configurations across network.
B.it includes an 8-bit field which specifies the priority of a frame.
C.it is used exclusively for tagging vlan frames and dose not address network reconvergence following switched network topology changes.
D.it modifies the 802.3 frame header,and thus requires that the FCS be recomputed.
E.it is a trunking protocol capable of carring untagged frames.
A.255.255.255.0
B.255.255.255.192
C.255.255.255.250
D.255.255.255.252
最新試題
傳輸層如何讓主機能同時針對不同應用程序維護多個通信流?()
要將數據包發送到遠程網絡,應使用哪種設備?()
請參見圖示。一臺路由器(其路由表如圖所示)收到發往192.168.1.4的數據包。路由器將如何處理該數據包?()
請參見圖示。下列哪組設備僅包含中間設備?()
請參見圖示。主機X 和主機Y 與本地網絡的通信受到限制。此問題的原因是什么?()
何時必須使用clock rate 命令配置路由器串行接口?()
請參見圖示。電纜1和電纜2分別按照特定的物理層要求接線。哪三個網段使用電纜2?()
請參見圖示。從主機X 發出的到主機Y 的tracert 命令已成功。下列哪一項正確地反映了追蹤列表中顯示的中間網絡設備的順序?()
OSI 哪一層可提供有序的數據重構服務?()
請參見圖示。RouterB 已經過正確配置。RouterA 的以太網接口Fa0/0已使用如圖所示的命令進行配置。但是,從RouterA 的Fa0/0接口無法成功ping 通RouterB 的Fa0/0接口。應在RouterA 上采取什么措施來解決此問題?()