A.802.11B
B.spanning-tree
C.802.1Q
D.ISL
E.VTP
F.Q.921
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. On the basis of the information provided in the exhibit, which two sets of procedures are best practices for Layer 2 and 3 failover alignment?（）
A. Configure the D-SW1 switch as the active HSRP router and the STP root for all VLANs. Configure the D-SW2 switch as the standby HSRP router and backup STP root for all VLANs.
B. Configure the D-SW1 switch as the standby HSRP router and the STP root for VLANs 11 and 110. Configure the D-SW2 switch as the standby HSRP router and the STP root for VLANs 12 and 120.
C. Configure the D-SW1 switch as the active HSRP router and the STP root for VLANs 11 and 110. Configure the D-SW2 switch as the active HSRP router and the STP root for VLANs 12 and 120.
D. Configure the D-SW2 switch as the active HSRP router and the STP root for all VLANs. Configure the D-SW1 switch as the standby HSRP router and backup STP root for all VLANs.
E. Configure the D-SW1 switch as the active HSRP router and the backup STP root for VLANs 11 and 110. Configure the D-SW2 switch as the active HSRP router and the backup STP root for VLANs 12 and 120.
F. Configure the D-SW1 switch as the standby HSRP router and the backup STP root for VLANs 12a nd 120. Configure the D-SW2 switch as the standby HSRP router and the backup STP root for VLANs 11 and 110.
A.Routing should occur at the access layer ifvoice VLANs are utilized. Otherwise， routing should occur at the distribution layer.
B.Routing should always be performed at the distribution layer.
C.VLANs should be localized to a switch.
D.VLANs should be localized to a single switch unlessvoice VLANs are being utilized.
E.Routing should not be performed between VLANs located on separate switches.
A.Topology-based switching
B.Demand-based switching
C.Route caching
D.Flow-based switching
E.None of the other alternatives apply
最新試題
Which two statements are true when the extended system ID feature is enabled？ （）
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this？（）
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain， the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change？（）
Which statement is correct about the use of the virtual interface on a WLC ？（）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
How are STP timers and state transitions affected when a topology change occurs in an STP environment？（）
Which three statements about STP timers are true？（）
Refer to the exhibit. What does the command channel-group 1 mode desirable do？ （）
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）