A. 0
B. 1
C. 2
D. 3
E. 4
F. 5
您可能感興趣的試卷
你可能感興趣的試題
When configuring vPC-HM CDP with multiple links to the same switch， are port-channels required？（）
A. Each link between the upstream switch and the VEM is an individual subgroup.
B. Connections that go to the same upstream switch must be configured with the command channel-group
C. Connections that go to the same upstream switch must be configured with the command channel-group
D. With vPC-HM CDP， the user can pin traffic from a specific VM to a specific uplink.
E. Connections that go to the same upstream switch must be configured with the command channel-group
A. 0
B. 1
C. 2
D. 3
E. 4
A. use summary view in the device manager
B. from the DCNM-SAN client， view ISLs in real time from the Performance drop-down list
C. for each port channel， select Monitor Continually
D. configure traps for each port channel to utilize RMON
E. set up flows with the DCNM-SAN client and use the Performance Manager web client for performance collections
A Host connected to an NPV switch is not able to see the storage connected to the core switch. Given the output of the show command below， what is the reason of this issue？（）
switch# show npv status
npiv is enabled
External Interfaces：
===============
InterfacE. fc1/1， VSAN： 1， FCID. 0x000000， StatE. Other
Number of External Interfaces： 4
A. NPV is not enabled on the core switch？
B. The interface connected to the Core switch is in admin down state
C. The local host interface belongs to the wrong VSAN？
D. The local host interface is not able to login
A. The switch receives the FCoE frame and forwards it to another switch over its VE port.
B. The switch receives the FCoE frame， deapsulates it， and sends the Fibre Channel frame to the fabric over its Fibre Channel uplink port.
C. The switch receives the FCoE frame， deapsulates it， and sends the Fibre Channel frame to the Fibre Channel target over its Fibre Channel port.
D. The switch receives the FCoE frame and forwards it to another FCoE device over its VN port.
最新試題
Given the following output： san-port-channel 12 is up Hardware is Fibre Channel Port WWN is 24：0c：00：0d：ec：d3：5c：00 Admin port mode is NP， trunk mode is on Port mode is NP Port vsan is 1 Speed is 8 Gbps Member[1] ： fc2/3 Member[2] ： fc2/4 What does "Speed is 8 Gbps" indicate？（）
Refer to the exhibit.Your company requires a Cisco UCS configuration that will， at a minimum， allow the configuration in the provided exhibit. Which Cisco UCS components will meet the requirement？（）
Your company wants Server 1/eth0 （vNIC 1） configured so that it always uses Fabric Interconnect A Port Channel 1 （Po1） when it communicates with anything outside of the Cisco UCS domain. However， if vNIC 1 fails over to Fabric Interconnect B using fabric failover， then vNIC 1 can any uplink port on Fabric Interconnect B. Which statements are true？ （）
Server load balancing （SLB） is the process of deciding to which server a load-balancing device should send a client request for service. Which predictors are supported on ACE in order to select the best server to fulfill a client request？ （）
Which statement is true regarding Backup tasks in Cisco UCS？（）
Application Control Engine （ACE） can check the health of servers and server farms by configuring health probes （which are sometimes referred to as keepalives）. A probe can be one of many types. Which are valid ACE probes？ （）
Refer to the exhibit.The Cisco UCS domain is operating in switching mode. A network administrator notices that no traffic is traversing the uplinks on Fabric Interconnect B （Path C）. Which actions might be used to change this behavior？（）
Where are SAN Port Channel is created in UCS Manager？（）
Which of the following are supported in Cisco Global Site Selector？ （）
Which three statements are possible causes for the "fltAdaptorHostIfLink-down" fault in UCS Manager？ （）