單項選擇題Which command sets and automatically encrypts the privileged enable mode password?()

A. enbale password c1sco
B. secret enable c1sco
C. password enable c1sco
D. enable secret c1sco


您可能感興趣的試卷

你可能感興趣的試題

1.單項選擇題Which statement is true?()

A. An IPv6 address is 64 b long and is represented as hexadecimal characters.
B. An IPv6 address is 32 b long and is represented as decimal digits.
C. An IPv6 address is 128 b long and is represented as decimal digits.
D. An IPv6 address is 128 b long and is represented as hexadecimal characters.

2.單項選擇題When upgrading the IOS image, the network administrator receives the exhibited error message. What could be the cause of this error?()

A. The new IOS image is too large for the router flash memory.
B. The TFTP server is unreachable from the router.
C. The new IOS image is not correct for this router platform.
D. The IOS image on the TFTP server is corrupt.
E. There is not enough disk space on the TFTP server for the IOS image.

3.單項選擇題

This graphic shows the results of an attempt to open a Telnet connection to router ACCESS1 from router Remote27. Which of the following command sequences will correct this problem? ()

A. ACCESS1(config)# line console 0 ACCESS1(config-line)# password cisco
B. Remote27(config)# line console 0 Remote27(config-line)# login Remote27(config-line)# password cisco
C. ACCESS1(config)# line vty 0 4 ACCESS1(config-line)# login ACCESS1(config-line)# password cisco
D. Remote27(config)# line vty 0 4 Remote27(config-line)# login Remote27(config-line)# password cisco
E. ACCESS1(config)# enable password cisco
F. Remote27(config)# enable password cisco

4.單項選擇題

A network administrator is troubleshooting the OSPF configuration of routers R1 and R2. The routers cannot establish an adjacency relationship on their common Ethernet link. The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2. Based on the information in the graphic, what is the cause of this problem?()

A. The OSPF area is not configured properly.
B. The priority on R1 should be set higher.
C. The cost on R1 should be set higher.
D. The hello and dead timers are not configured properly.
E. A backup designated router needs to be added to the network.
F. The OSPF process ID numbers must match.

最新試題

Three access ports have been installed and configured to a small office.What term defines the wireless topology?()

題型:單項選擇題

Which IPsec security protocol should be used when confidentiality is required?()

題型:單項選擇題

At which layer of the OSI model dose PPP perform?()

題型:單項選擇題

Three switches are connected to one anther via trunk ports.Assuming the default switch configuration,which switch is elected as the root bridge for the spanning-tree instance of vlan 1?()

題型:單項選擇題

Which command is used to display the collection of OSPF link states?()

題型:單項選擇題

A router receives information about network 192.168.10.0/24 from multiple sources.What will the router consider the most reliable information about the path to that network?()

題型:單項選擇題

A network administrator needs to configure a serial link between the main office and a remote location.The router at the remote office is a non-cisco router. How should the network administrator configure the serial interface of the main office router to make the connection?()

題型:單項選擇題

Which device might be installed at a branch office to enable and manage an IPsec site-to-site VPN?()

題型:單項選擇題

Which command encrypts all plaintext passwords?()

題型:單項選擇題

Which protocol reduces administrative overhead in a switched network by allowing the configuration of a new VLAN to be distributed to all the switches in a domain?()

題型:單項選擇題