A. IP address:192.168.20.14 Subnet Mask:255.255.255.248 Default Gateway:192.168.20.9
B. IP address:192.168.20.254 Subnet Mask:255.255.255.0 Default Gateway:192.168.20.1
C. IP address:192.168.20.30 Subnet Mask:255.255.255.248 Default Gateway:192.168.20.25
D. IP address:192.168.20.30 Subnet Mask:255.255.255.240 Default Gateway:192.168.20.17
E. IP address:192.168.20.30 Subnet Mask:255.255.255.240 Default Gateway:192.168.20.25
您可能感興趣的試卷
你可能感興趣的試題
A. STP
B. VTP
C. GVRP
D. SNMP
E. DHCP
A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem?（）
Router(config)#router ospf 1
Router(config-router)#network 10.0.0.0 255.0.0.0 area 0
A. The process id is configured improperly
B. The OSPF area is configured improperly
C. The network wildcard mask is configured improperly
D. The network number is configured improperly
E. The AS is configured improperly
F. The network subnet mask is configuerd improperly
A. the IP address of the first Fast Ethernet interface
B. the IP address of the console management interface
C. the highest IP address among its active interfaces
D. the lowest IP address among its active interfaces
E. the priority value until a loopback interface is configured
A. IBSS
B. BSS
C. ESS
D. SSID
The network administrator cannot to switch 1 over a telnet session,although the hosts attached to switch 1 can ping the interface Fa0/0 of the router.Given the information in the graphic and assuming that the router and switch2 are configured properly,which of the following commands should be issued on switch 1 to correct this problem?（）
A. Switch1(config)# i nterface fa0 /1 Switch1(config-if)# ip address 192.168.24.3.255.255.255.0
B. Switch1 (config)#interface fa0/1 Switch1 (config-if)# switchport mode trunk
C. Switch 1 (config)# i nterface fa0 /1 Switch1 (config-if)# duplex full Switch1 (config-if)# speed 100
D. Switch1 (config-if)# default-gateway 192.168.24.1
E. Switch1 (config)# line con 0 Switch1(config-line)# password cisco Switch1 (config-line)#login
最新試題
The network administrator cannot to switch 1 over a telnet session,although the hosts attached to switch 1 can ping the interface Fa0/0 of the router.Given the information in the graphic and assuming that the router and switch2 are configured properly,which of the following commands should be issued on switch 1 to correct this problem?（）
Which name describes an IPV6 host-enable tunneling technique that uses IPV4 UDP,does not require dedicated gateway tunnels,and can pass through existing IPV4 NAT gateways?（）
What is the purpose of the cisco Vlan Trunking protocol?（）
While troubleshooting a network problem,a technician discovers that the current copy of the Cisco IOS is outdated and needs to be updated.Which of the following commands would the technician issue to replace the Cisco router IOS with the newer version?（）
Which command is used to display the collection of OSPF link states?（）
An employee of ABC company has move to an office on a different floor. Although the administrator is able to telnet to all of the routers,the address of Switch F is needed in order to verify that the employee remains in the same VLAN.Which action could be used by the administrator to find the IP address of Switch F?（）
If all OSPF routers in a single area are configured with the same priority value,what value dose a router use for the ODPF router ID in the absence of a loopback interface?（）
A network administrator needs to configure a serial link between the main office and a remote location.The router at the remote office is a non-cisco router. How should the network administrator configure the serial interface of the main office router to make the connection?（）
A router receives information about network 192.168.10.0/24 from multiple sources.What will the router consider the most reliable information about the path to that network?（）
When you are troubleshooting an ACL issue on a router,which command can help you to verify which interfaces are affected by the ACL?（）