A.The IBGP routers must always be fully meshed.
B.The IBGP routers can be in a different AS.
C.The IBGP routers must be directly connected.
D.TThe IBGP routers do not need to be directly connected.
E.None of the other alternatives apply are true
您可能感興趣的試卷
你可能感興趣的試題
A network administrator is troubleshooting an EIGRP connection between RouterA， IP address10.1.2.1， and RouterB， IP address 10.1.2.2. Given the debug output on RouterA， which twostatements are true？（）
A.RouterA received a hello packet with mismatched metric-calculation mechanisms
B.RouterA received a hello packet with mismatched authentication parameters
C.RouterA will form an adjacency with RouterB
D.RouterA received a hello packet with mismatched autonomous system numbers
E.RouterA received a hello packet with mismatched hello timers
F.RouterA will not form an adjacency with RouterB
The following command was issued on Router 2：
Given the above output shown above， which statement is true？（）
A.192.168.1.0 is a redistributed route into EIGRP
B.192.168.1.0 is a summarized route
C.192.168.1.0 is a static route
D.192.168.1.0 is equal path load balancing with 172.16.1.0
E.None of the other alternatives apply
The EIGRP network is displayed in the following topology diagram：
You work as a network technician. Study the exhibits carefully. If the command "variance 3" wasadded to the EIGRP configuration of R5， which path or paths would be chosen to route traffic fromR5 to network X？（）
A.R5-R2-R1
B.R5-R2-R1 and R5-R3-R1
C.R5-R3-R1 and R5-R4-R1
D.R5-R2-R1，R5-R3-R1， and R5-R4-R1
A.Use the service-policy command to adjust the QOS policy to allow the route to propagate.
B.Clear the BGP session.
C.Use the release BGP routing command.
D.Change both the inbound and outbound policy related to this route.
E.None of the other alternatives apply
The network is shown below， along with the relevant router configurations：
With the topology found in the graphic， what will the R1 loopback 0 be in the R3 routing table？（）
A.It will show up in the routing table as D 10.0.0/8
B.It will show up in the routing table as D EX 10.0.0.0/8
C.It will show up in the routing table as D 10.0.0./24
D.It will not show up in R3 routing table because there is no network command on R1
最新試題
IPSec VPN is a widely-acknowledged solution for enterprise network. What are the four steps tosetup an IPsec VPN？（）
Which three statements accurately describe IOS Firewall configurations？（）
Authentication is the process of determining if a user or identity is who they claim to be. Refer tothe exhibit. Which statement about the authentication process is correct？（）
A new router was configured with the following commands：The configuration above was found on an Internet Service Provider’s （ISP） Multiprotocol LabelSwitching （MPLS） network. What is its purpose？（）
As a network engineer， do you know for what purpose SDM uses Security Device Event Exchange（SDEE）？（）
Router NetworkTut is configured as shown below：Given the above configuration， which statement is true？（）
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clickingthe numbers to the left of each question. In order to complete the questions， you will need to referto the SDM and the topology， neither of which is currently visible. To gain access to either thetopology or the SDK click on the button to left side of the screen that corresponds to the sectionyou wish to access. When you have finished viewing the topology the SDK you can return to yourquestions by clicking on the Questions button to the left.Which IPSec rule is used for the Olympia branch and what does it define？（）
As a network engineer， study the exhibit carefully. Router Net is unable to establish an ADSLconnection with its provider. Which action would correct this problem？（）
Identify the recommended steps for worm attack mitigation by dragging and dropping them into thetarget area in the correct order.
Drag the IOS commands from the left that would be used to implement a GRE tunnel using the10.1.1.0.30 network on interface serial 0/0 to the correct target area on the right.