單項選擇題You are securing a network for TestKing and want to apply an ACL (access control list) to an interface of a router. Which one of the following commands would you use?（）

A. permit access-list 101 out
B. ip access-group 101 out
C. apply access-list 101 out
D. access-class 101 out
E. ip access-list e0 out


您可能感興趣的試卷

你可能感興趣的試題

1.單項選擇題What is the purpose of assigning an IP address to a switch?（）

A. Provides local hosts with a default gateway address
B. Allows remote management of the switch.
C. Allows the switch to respond to ARP requests between two hosts
D. Ensures that hosts on the same LAN can communicate with each other.

2.單項選擇題As a TestKing trainee you are required to set the default gateway on a Cisco switch to the IP address of 192.168.1.115. Which IOS command should you use?（）

A. TestKSwitch(config)# ip route-default 192.168.1.115
B. TestKSwitch(config)# ip default-gateway 192.168.1.115
C. TestKSwitch(config)# ip route 192.168.1.115 0.0.0.0
D. TestKSwitch(config)# ip default-network 192.168.1.115

3.多項選擇題Which interface commands would you enter on a Catalyst 2900 switch, if your goal was to bring all VLAN traffic to another directly connected switch?（）

A. Switch(config-if)# vlan all
B. Switch(config-if)# switchport trunk encapsulation dot1q
C. Switch(config-if)# switchport access vlan all
D. Switch(config-if)# switchport mode trunk
E. Switch(config-if)# switchport access vlan 303

5.單項選擇題After making some network changes you power off and then power on your Cisco router. What sequence of events occurs when a router is powered up?（）

A. Perform POST, locate configuration statements, apply configuration statements, locate Cisco IOS software, and load Cisco IOS software.
B. Locate Cisco IOS software, load Cisco IOS software, locate configuration statements, apply configuration statements, and perform POST.
C. Test software routines, POST, load configuration files, load Cisco IOS software, test Cisco IOS software.
D.POST, locate Cisco IOS software, load the Cisco IOS software, locate configuration statements, and apply configuration statements.
E. Load and test IOS, load configuration files, test software routines, POST.

最新試題

What is the subnetwork address for a host with IP address 201.100.5.68/28?（）

題型：單項選擇題

Identify three valid host addresses in the 192.168.27.0 network with a subnet mask of 255.255.255.240. （）

題型：多項選擇題

An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location? （）

題型：多項選擇題

Which of the following contribute to congestion on an Ethernet network?（）

題型：多項選擇題

The following access list was applied outbound on he E0 interface connected to the 192.168.1.8/29 LAN:access-list 123 deny tcp 192.168.1.8 0.0.0.7 eq 20 anyaccess-list 123 deny tcp 192.168.1.9 0.0.0.7 eq 21 anyWhat effect will this access list have?（）

題型：單項選擇題

Which of the following options lists the steps in PPP session establishment in the correct order?（）

題型：單項選擇題

What does a configuration Register Setting of 0x2105 indicate to the Router? （）

題型：單項選擇題

Which of the following statements regarding routed and routing protocols are true?（）

題型：多項選擇題

Which command is used to display the placement and direction of an IP access control list on a router?（）

題型：單項選擇題

New switches have been purchased for a network upgrade. The objective for the network design emphasizes efficient, error-free transport instead of fast transport.Which switching mode should be configured on the new switches to provide error-free transport to the network? （）

題型：單項選擇題