The Company network utilizes the Multiple-instance Spanning Tree protocol in its switched LAN.
Which three statements about the MST protocol （IEEE 802.1S） are true？ （）
A. To verify the MST configuration， the show pending command can be used in MST configuration mode.
B. When RSTP and MSTP are configured； UplinkFast and BackboneFast must also be enabled.
C. All switches in the same MST region must have the same VLAN-to-instance mapping， but different configuration revision numbers.
D. All switches in an MST region， except distribution layer switches， should have their priority lowered from the default value 32768.
E. An MST region is a group of MST switches that appear as a single virtual bridge to adjacent CST and MST regions.
F. Enabling MST with the "spanning-tree modemst" global configuration command also enables RSTP.
您可能感興趣的試卷
你可能感興趣的試題
On switch R1 you issue the "udld enable" global command.
What does this command accomplish？ （）
A. Enables all fiber-optic LAN ports for Unidirectional LINK Detection （UDLD）
B. Enables all copper media LAN ports Unidirectional Link Detection （UDLD）
C. Overrides the default UDLS setting for all ports
D. Globally enables all ports on the device for Unidirectional Link Detection （UDLS）
E. None of the other alternatives apply
Switch R1 has been configured with the root guard feature.
What statement is true if the spanning tree enhancement Root Guard is enabled？ （）
A. If BPDUs are not received on a non-designated port， the port is moved into the STP loop- inconsistent blocked state
B. IF BPDUs are received on a PortFast enabled port， the port is disabled.
C. If superior BPDUs are received on a designated port， the interface is placed into the root- inconsistent blocked state.
D. If inferior BPDUs are received on a root port， all blocked ports become alternate paths to the root bride.
You are the network administrator tasked with designing a switching solution for the Company network.
Which of the following statements describing trunk links are INCORRECT？（）
A. The trunk link belongs to a specific VLAN.
B. Multiple trunk links are used to connect multiple end user devices.
C. A trunk link only supports native VLAN.
D. Trunk links use 802.10 to identify a VLAN.
E. The native VLAN of the trunk link is the VLAN that the trunk uses for untagged packets.
ISL is being configured on a Company switch.
Which of the following choices are true regarding the ISL protocol？ （）
A. It can be used between Cisco and non-Cisco switch devices.
B. It calculates a new CRC field on top of the existing CRC field.
C. It adds 4 bytes of protocol-specific information to the original Ethernet frame.
D. It adds 30 bytes of protocol-specific information to the original Ethernet frame.
Which of the following trunking modes are unable to request their ports to convert their links into trunk links？ （）
A. Negotiate
B. Designate
C. No negotiate
D. Auto
E. Manual
F. Off
最新試題
Which three statements are true of the Link Aggregation Control Protocol （LACP）？（）
Which three statements about STP timers are true？（）
Which router redundancy protocol cannot be configured for interface tracking？（）
Which two statements are true about BPDU port-guard and BPDU filtering？（）
Which statement is correct about RSTP port roles？（）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
Refer to the exhibit. What will happen when one more user is connected to interface FastEthernet 5/1？ （）
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this？（）
Refer to the exhibit. Which Virtual Router Redundancy Protocol （VRRP） statement is true about the roles of the master virtual router and the backup virtual router？（）
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ？ （）