Refer to the exhibit. Switch P1S1 is not applying VLAN updates from switch P2S1.
What are three reasons why this is not occurring？（）
A. Switch P2S1 is in server mode.
B. Switch P1S1 is in transparent mode.
C. The MD5 digests do not match.
D. The passwords do not match.
E. The VTP domains are different.
F. VTP trap generation is disabled on both switches.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the show interface Gi0/1 switchport command output shown in the exhibit.
Which two statements are true about this interface？（）
A. This interface is a member of a voice VLAN.
B. This interface is configured for access mode.
C. This interface is a dot1q trunk passing all configured VLANs.
D. This interface is a member of VLAN7.
E. This interface is a member of VLAN1.
You’re a network administer and you issue the command （show port 3/1） on an Ethernet port. To your surprise you notice a non-zero entry in the ’Giants’ column.
What could be the cause of this？ （）
A. IEEE 802.1Q
B. IEEE 802.10
C. Misconfigured NIC
D. User configuration
E. All of the above
The Company administrator has issue the "show vlan id 5" command.
What will this command display？ （）
A. Ports in VLAN 5
B. Utilization
C. VLAN information on port 0/5
D. Filters
E. MTU and type
Which of the following should you enable to prevent a switch from forwarding packets with source addresses that are outside an administratively defined group？ （）
A. DAI
B. STP
C. PVLAN
D. port security
Refer to the exhibit. The switchport output in Figure 1 displays the default settings of interface FastEthernet 0/13 on switch SW1. Figure 2 displays the desired interface settings.
Which command sequence would configure interface FastEthernet 0/13 as displayed in Figure 2？ （）
A. SW1（config-if）# switchport trunk encapsulation dot1q SW1（config-if）# switchport mode trunk SW1（config-if）# switchport trunk native DATA SW1（config-if）# switchport trunk allowed vlan 1，10，20
B. SW1（config-if）# switchport trunk encapsulation dot1q SW1（config-if）# switchport mode dynamic auto SW1（config-if）# switchport trunk native DATA SW1（config-if）# witchport trunk allowed vlan add 1，10，20
C. SW1（config-if）# switchport trunk encapsulation dot1q SW1（config-if）# switchport mode dynamic desirable SW1（config-if）# switchport trunk native vlan DATA SW1（config-if）# switchport trunk allowed vlan 1，10，20
D. SW1（config-if）# switchport trunk encapsulation dot1q SW1（config-if）# switchport mode dynamic desirable SW1（config-if）# switchport trunk native vlan 10 SW1（config-if）# switchport trunk allowed vlan 1，10，20
E. SW1（config-if）# switchport trunk encapsulation dot1q SW1（config-if）# switchport mode dynamic Desirable SW1（config-if）# switchport trunk native vlan 10
最新試題
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this？（）
Refer to the exhibit. On the basis of the output of the show spanning-tree inconsistentports command， which statement about interfaces FastEthernet 0/1 and FastEthernet 0/2 is true？（）
Which router redundancy protocol cannot be configured for interface tracking？（）
Which two statements are true about BPDU port-guard and BPDU filtering？（）
Refer to the exhibit. Which Virtual Router Redundancy Protocol （VRRP） statement is true about the roles of the master virtual router and the backup virtual router？（）
Which two statements are true when the extended system ID feature is enabled？ （）
If G1/0/1 on DS1 is shutdown， what will be the current priority value of the Vlan105’s group on DS1 ？（）
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link？（）
Which statement is correct about RSTP port roles？（）