Refer to the exhibit. Based on the running configuration that is shown for interface FastEthernet0/2，
what two conclusions can be deduced？（）
A. Connecting a host with MAC address 0000.0000.4147 will move interface FastEthernet0/2 into error disabled state.
B. The host with address 0000.0000.4141 is removed from the secure address list after 5 seconds of inactivity.
C. The sticky secure MAC addresses are treated as static secure MAC addresses after the running configuration is saved to the startup configuration and the switch is restarted.
D. Interface FastEthernet0/2 is a voice VLAN port.
E. The host with address 0000.0000.000b is removed from the secure address list after 300 seconds.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit.
Which interface or interfaces on switch SW_A can have the port security feature enabled？（）
A. Ports 0/1 and 0/2
B. The trunk port 0/22 and the EtherChannel ports
C. Ports 0/1， 0/2 and 0/3
D. Ports 0/1， 0/2， 0/3， the trunk port 0/22 and the EtherChannel ports
E. Port 0/1
F. Ports 0/1， 0/2， 0/3 and the trunk port 0/22
A Company switch was configured as shown below：
switchport mode access switchport port-security
switchport port-security maximum 2
switchport port-security mac-address 0002.0002.0002
switchport port-security violation shutdown
Given the configuration output shown above，
what happens when a host with the MAC address of 0003.0003.0003 is directly connected to the switch port？ （）
A. The host will be allowed to connect.
B. The port will shut down.
C. The host can only connect through a hub/switch where 0002.0002.0002 is already connected.
D. The host will be refused access.
E. None of the other alternatives apply
VLAN maps have been configured on switch R1.
Which of the following actions are taken in a VLAN map that does not contain a match clause？ （）
A. Implicit deny feature at end of list.
B. Implicit deny feature at start of list.
C. Implicit forward feature at end of list
D. Implicit forward feature at start of list.
Refer to the exhibit. The web servers WS_1 and WS_2 need to be accessed by external and internal users. For security reasons， the servers should not communicate with each other，
although they are located on the same subnet. The servers do need， however， to communicate with a database server located in the inside network.
What configuration will isolate the servers from each other？ （）
A. The switch ports 3/1 and 3/2 will be defined as secondary VLAN community ports. The ports connecting to the two firewalls will be defined as primary VLAN promiscuous ports.
B. The switch ports 3/1 and 3/2 and the ports connecting to the two firewalls will be defined as primary VLAN promiscuous ports.
C. The switch ports 3/1 and 3/2 and the ports connecting to the two firewalls will be defined as primary VLAN community ports.
D. The switch ports 3/1 and 3/2 will be defined as secondary VLAN isolated ports. The ports connecting to the two firewalls will be defined as primary VLAN promiscuous ports.
pany is implementing 802.1X in order to increase network security. In the use of 802.1X
access control，
which three protocols are allowed through the switch port before authentication takes place？ （）
A. EAP-over-LAN
B. EAP MD5
C. STP
D. protocols not filtered by an ACL
E. CDP
F. TACACS+
最新試題
Which statement is correct about the use of the virtual interface on a WLC ？（）
Refer to the exhibit. Which statement is true about the output？（）
If G1/0/1 on DS1 is shutdown， what will be the current priority value of the Vlan105’s group on DS1 ？（）
How are STP timers and state transitions affected when a topology change occurs in an STP environment？（）
Which three statements about STP timers are true？（）
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ？ （）
What two things will occur when an edge port receives a BPDU？（）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Which two statements are true about BPDU port-guard and BPDU filtering？（）