What is true about access control on bridged and routed VLAN traffic？ （）
A. Router ACLs can be applied to the input and output directions of a VLAN interface.
B. Bridged ACLs can be applied to the input and output directions of a VLAN interface.
C. Only router ACLs can be applied to a VLAN interface.
D. VLAN maps and router ACLs can be used in combination.
E. VLAN maps can be applied to a VLAN interface
您可能感興趣的試卷
你可能感興趣的試題
On a Company switch named R1 you configure the following： iparp inspection vlan 10-12， 15
What is the purpose of this global configuration command made on R1？（）
A. Discards ARP packets with invalid IP-to-MAC address bindings on trusted ports
B. Validates outgoing ARP requests for interfaces configured on VLAN 10， 11， 12， or 15
C. Intercepts， logs， and discards ARP packets with invalid IP-to-MAC address bindings
D. Intercepts all ARP requests and responses on trusted ports
E. None of the other alternatives apply
As the network technician at Company， you need to configure DHCP snooping on a new switch.
Which three steps are required？ （）
A. Configure the switch to insert and remove DHCP relay information （option-82 field） in forwarded DHCP request messages.
B. Configure DHCP snooping globally.
C. Configure the switch as a DHCP server.
D. Configure DHCP snooping on an interface.
E. Configure all interfaces as DHCP snooping trusted interfaces.
F. Configure DHCP snooping on a VLAN or range of VLANs.
In the use of 802.1X access control，
which three protocols are allowed through the switch port before authentication takes place？ （）
A. STP
B. CDP
C. EAP MD5
D. TACACS+
E. EAP-over-LAN
F. protocols not filtered by an ACL
The DAI feature has been implemented in the Company switched LAN.
Which three statements are true about the dynamic ARP inspection （DAI） feature？ （）
A. DAI can be performed on ingress ports only.
B. DAI can be performed on both ingress and egress ports.
C. DAI is supported on access ports， trunk ports， EtherChannel ports， and private VLAN ports.
D. DAI should be enabled on the root switch for particular VLANs only in order to secure the ARP caches of hosts in the domain.
E. DAI should be configured on all access switch ports as untrusted and on all switch ports connected to other switches as trusted.
F. DAI is supported on access and trunk ports only.
pany has implemented 802.1X authentication as a security enhancement.
Which statement is true about 802.1x port-based authentication？（）
A. TACACS+ is the only supported authentication server type.
B. If a host initiates the authentication process and does not receive a response， it assumes it is not authorized.
C. RADIUS is the only supported authentication server type.
D. Before transmitting data， an 802.1x host must determine the authorization state of the switch.
E. Hosts are required to havea 802.1x authentication client or utilize PPPoE.
F. None of the other alternatives apply.
最新試題
What is the configured priority value of the Vlan105’s group on DS2 ？（）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
Refer to the exhibit. All network links are FastEthernet. Although there is complete connectivity throughout the network， Front Line users have been complaining that they experience slower network performance when accessing the server farm than the Reception office experiences. Based on the exhibit， which two statements are true？（）
Refer to the exhibit. What will happen when one more user is connected to interface FastEthernet 5/1？ （）
Which three statements are true of the Link Aggregation Control Protocol （LACP）？（）
Which router redundancy protocol cannot be configured for interface tracking？（）
During routine maintenance， it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time， DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ？ （）
Refer to the exhibit. Which statement is true about the output？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ？ （）