On your OSPF network, routers TK1 and TK2 belong to the same Ethernet network. However, they are unable to establish an adjacency over this link. While troubleshooting this problem, you issue the "show ip ospf interface Ethernet 0"command on each router. The output from these commands is displayed below:
What is the underlying cause of the routers failing to become adjacent?()
A. The OSPF area is misconfigured.
B. The priority on TK2 should be set lower.
C. The cost on TK2 should be set lower.
D. The hello and dead timers are misconfigured.
E. You need to add a backup designated router to the network.
F. The OSPF process ID numbers do not match.
您可能感興趣的試卷
你可能感興趣的試題
While trying to diagnose a routing problem in the network, you issue RIP debugging as displayed below:
RtrA#debug ip rip
Rip protocol debugging is on
RtrA#
1d05h: RIP: sending v1 update to 255.255.255.255 via FastEthernet0/0 (172.16.1.1)
1d05h: RIP: build update entries
1d05h: network 10.0.0.0 metric 1
1d05h: network 192.168.1.0 metric 2
1d05h: RIP: sending v1 update to 255.255.255.255 via Serial0/0 (10.0.8.1)
1d05h: RIP: build update entries
1d05h: network 172.16.0.0 metric 1
RtrA#
1d05h: RIP: received v1 update from 10.0.15.2 on Serial0/0
1d05h: 192.168.1.0 in 1 hops
1d05h: 192.168.0 in 16 hops (inaccessible)
Based on the output of the above exhibit, which two of the following statements are true?()
A. A ping to 10.0.15.2 will be successful.
B. RtrA has three interfaces that will take part in the RIP process.
C. There are at least two routers participating in the RIP process.
D. A ping to 192.168.168.2 will be successful.
A. TK1# show ip ospf interface
B. TK1# show ip ospf priority
C. TK1# show ospf neighbor detail
D. TK1# show ospf processes
E. TK1# show ospf neighbor state
A. Each end of the trunk line must be set to IEEE 802.1E encapsulation.
B. The VTP management domain name of both switches must be set the same.
C. All ports on both the switches must be set as access port.
D. One of the two switches must be configured as a VTP server.
E. A rollover cable is required to connect the two switches together.
F. A router must be used to forward VTP traffic between VLANs.
A. Ping
B. Tracert
C. Ipconfig
D. Show ip route
E. Winipcfg
F. Show interfaces
A. ping
B. tracert
C. ipconfig
D. show ip route
E. winipcfg
F. show interfaces
G. All of the above
最新試題
Which of the following statements regarding routed and routing protocols are true?()
What feature of a networks switch allows an administrative to create separate broadcast domains?()
Which command is used to display the placement and direction of an IP access control list on a router?()
What is the subnetwork address for a host with IP address 201.100.5.68/28?()
TestKing.com has allocated the IP add 199.144.27.0 is its network, to provide flexibility for the LAN design, a subnet mask of 255.255.255.240 has been chosen. Which of the following address can be assigned to LAN on the resulting subnets.()
An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location? ()
A router with a serial interface will be used for an ISDN link.What other function group devices are required to complete the connection to the service provider? ()
The following access list was applied outbound on he E0 interface connected to the 192.168.1.8/29 LAN:access-list 123 deny tcp 192.168.1.8 0.0.0.7 eq 20 anyaccess-list 123 deny tcp 192.168.1.9 0.0.0.7 eq 21 anyWhat effect will this access list have?()
What is the purpose of typing o/r 0x2142 during a password recover procedure on a 2500 series router?()
The network 172.12.0.0 needs to be divided into subnets where each subnet has the capacity of 458 IP addresses.What would be the correct subnet mask to accomplish this division keeping the number of subnets at the maximum? ()