A hacker on the Company network is attempting to hop onto a different VLAN.
Which two statements about VLAN hopping are true？ （）
A. An end station attempts to gain access to all VLANs by transmitting Ethernet frames in the 802.1q encapsulation.
B. Configuring an interface with the "switchport mode dynamic" command will prevent VLAN hopping.
C. Attacks are prevented by utilizing the port-security feature.
D. Configuring an interface with the "switchport mode access" command will prevent VLAN hopping.
E. An end station attempts to redirect VLAN traffic by broadcasting multiple ARP requests.
您可能感興趣的試卷
你可能感興趣的試題
The Company security administrator wants to prevent VLAN hopping on the network.
What is one method that can be used to do this？ （）
A. Attacks are prevented by utilizing the port-security feature.
B. An end station attempts to gain access to all VLANs by transmitting Ethernet frames in the 802.1q encapsulation.
C. Configuring an interface with the switchport mode dynamic command will prevent VLAN hopping.
D. An end station attempts to redirect VLAN traffic by transmitting Ethernet frames in the 802.1q encapsulation.
E. Configuring an interface with the "switchport mode access" command will prevent VLAN hopping.
The Company security administrator is concerned with VLAN hopping based attacks.
Which two statements about these attacks are true？ （）
A. Attacks are prevented by utilizing the port-security feature.
B. An end station attempts to gain access to all VLANs by transmitting Ethernet frames in the 802.1q encapsulation.
C. Configuring an interface with the switchport mode dynamic command will prevent VLAN hopping.
D. An end station attempts to redirect VLAN traffic by transmitting Ethernet frames in the 802.1q encapsulation.
E. Configuring an interface with the "switchport mode access" command will prevent VLAN hopping.
Refer to the exhibit. PCs in VLAN 2 are not able to communicate with PCs in VLAN 3.
What could be the cause？（）
A. IP routing is not enabled.
B. VTP is not configured correctly on the interfaces.
C. The command mls rp management-interface is missing.
D. The command mls rp ip must be disabled to enable the routing.
You are configuring a Cisco multilayer switch for the Company network.
Which command would you use to configure a port to act as a routed interface？（）
A. ip routing
B. switchport mode trunk
C. no switchport
D. switchport trunk native vlan 1
E. None of the other alternatives apply
Which of the following could be used to provide a Layer 3 data path between separate VLANs？（）
A. VLAN trunking
B. An external router
C. An internal route processor
D. VLAN capable bridge
E. EtherChannel
最新試題
Refer to the exhibit. On the basis of the output of the show spanning-tree inconsistentports command， which statement about interfaces FastEthernet 0/1 and FastEthernet 0/2 is true？（）
How are STP timers and state transitions affected when a topology change occurs in an STP environment？（）
Which two statements are true when the extended system ID feature is enabled？ （）
Refer to the exhibit. For what purpose is the command show ip cef used？（）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
Which two statements are true about BPDU port-guard and BPDU filtering？（）
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Refer to the exhibit. Which statement is true about the output？（）
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）