LDAP is being used throughout the Company wireless network.
Which statement about the Lightweight Access Point Protocol （LWAPP） protocol is true？（）
A. The processing of 802.11 data and management protocols and access point capabilities is distributed between a lightweight access point and a centralized WLAN controller.
B. LWAPP advertises its WDS capability and participates in electing the best WDS device for the wireless LAN.
C. LWAPP aggregates radio management forward information and sends it to a wireless LAN solution engine.
D. LWAPP authenticates all access points in the subnet and establishes a secure communication channel with each of them.
E. None of the other alternatives apply
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. Both host stations are part of the same subnet but are in different VLANs. On the basis of the information presented in the exhibit，
which statement is true about an attempt to ping from host to host？ （）
A. The two different hosts will need to be in the same VLAN in order for the ping command to be successful.
B. A Layer 3 device is needed for the ping command to be successful.
C. The ping command will be successful without any further configuration changes.
D. A trunk port will need to be configured on the link between Sw_A and Sw_B for the ping command to be successful.
Based on the network diagram and routing table output in the exhibit，
which of these statements is true？ （）
A. InterVLAN routing will not occur since no routing protocol has been configured.
B. InterVLAN routing has been configured properly， and the workstations have connectivity to each other.
C. Although interVLAN routing is not enabled， both workstations will have connectivity to each other.
D. Although interVLAN routing is enabled， the workstations will not have connectivity to each other.
Refer to the exhibit. VLAN2， VLAN3， and VLAN10 are configured on the switch D-SW1. Host computers are on VLAN 2 （10.1.2.0）， servers are on VLAN 3 （10.1.3.0）， and the management VLAN is on VLAN10 （10.1.10.0）. Hosts are able to ping each other but are unable to reach the servers. On the basis of the exhibited output，
which configuration solution could rectify the problem？（）
A. Assign an IP address of 10.1.3.1/24 to VLAN3.
B. Configure default gateways to IP address 10.1.10.1 on each host.
C. Enable IP routing on the switch D-SW1.
D. Configure a default route that points toward network 200.1.1.0/24.
E. Configure default gateways to IP address 10.1.2.1 on each host.
F. Configure default gateways to IP address 200.1.1.2 on each host.
Refer to the exhibit. Host A and Host B are connected to the Catalyst 3550 switch and have been assigned to their respective VLANs. The rest of the 3550 configuration is the default configuration. Host A is able to ping its default gateway， 10.10.10.1， but is unable to ping Host B. Given the output displayed in the exhibit，
which statement is true？ （）
A. A separate router is required to support interVLAN routing.
B. VTP must be configured to support interVLAN routing.
C. VLANs 10 and 15 must be created in the VLAN database mode.
D. The global config command ip routing must be configured on the SW1 switch.
E. HSRP must be configured on SW1.
F. Interface VLAN 10 must be configured on the SW1 switch.
Refer to the exhibit. Dynamic ARP inspection （DAI） is enabled on switch SW_A only. Both Host_A and Host_B acquire their IP addresses from the DHCP server connected to switch SW_A.
What would the outcome be if Host_B initiated an ARP spoof attack toward Host_A ？ （）
A. The spoof packets will be inspected at the ingress port of switch SW_A and will be permitted.
B. The spoof packets will not be inspected at the ingress port of switch SW_A and will be permitted.
C. The spoof packets will not be inspected at the ingress port of switch SW_A and will be dropped.
D. The spoof packets will be inspected at the ingress port of switch SW_A and will be dropped.
最新試題
Which statement is correct about RSTP port roles？（）
Refer to the exhibit. What will happen when one more user is connected to interface FastEthernet 5/1？ （）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
Which two statements are true when the extended system ID feature is enabled？ （）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
How are STP timers and state transitions affected when a topology change occurs in an STP environment？（）
Refer to the exhibit. What does the command channel-group 1 mode desirable do？ （）
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ？ （）
What is the configured priority value of the Vlan105’s group on DS2 ？（）
Which two statements are true about BPDU port-guard and BPDU filtering？（）