A. ping
B. trace
C. show ip route
D. show interface
E. show cdp neighbors
您可能感興趣的試卷
你可能感興趣的試題
A. Serial 0 is up, line protocol is up
B. Serial 0 is up, line protocol is down
C. Serial 0 is down, line protocol is down
D. Serial 0 is down, line protocol is up
E. Serial 0 is administratively down, line protocol is down
F. Serial 0 is administratively down, line protocol is up
There is a connectivity problem between the serial 0/0 interface of router TESTKING1 and the serial 0/0 interface of TESTKING2. A leased line point to point circuit is installed between these two routers. The output from the "show interface serial 0/0" command is displayed below for each of these routers:
From your observations of the above exhibit, what is the underlying cause of the problem?（）
A. The loopback is not set.
B. The serial cable is faulty.
C. The subnet mask is not configured properly.
D. The IP address is not configured properly.
E. The Layer 2 frame types are not compatible.
F. The keepalive setting is not configured properly.
The relevant configuration files for the TestKing1 and TestKing2 routers are displayed below:
With due consideration to the command outputs, which of the following reasons would you attribute the connectivity problem between the two routers?（）
A. The authentication needs to be changed to PAP for both routers.
B. The serial IP addresses of routers are not on the same subnet.
C. The username/password combination is incorrectly configured.
D. The router names are incorrectly configured.
A. ICMP echo request
B. Information interrupt request
C. Timestamp reply
D. Source quench
E. None of the above
The Testking router is running RIP as the routing protocol, and the IP routing table is displayed below:
Gateway of last resort is 10.1.2.2 to network 0.0.0.0
10.0.0.0/24 is subnetted, 2 subnets
R 10.1.3.0 [120/1] via 10.1.2.2, 00:00:00, Serial0/0
C 10.1.2.0 is directly connected, Serial0/0
C 10.1.5.0 is directly connected, Serial0/1
C 10.1.6.0 is directly connected, FastEthernet0/0
R* 0.0.0.0/0 [120/1] via 10.1.5.5, 00:00:00, Serial0/1
Based on the output above, if an administrator pings host 10.1.8.5 from host
10.1.6.100, how will the router TestkingA process the ICMP packets?（）
A. The packets will be discarded.
B. The packets will be routed out the S0/0 interface.
C. The packets will be routed out the S0/1 interface.
D. The packets will be routed out the Fa0/0 interface.
E. The packets will be routed through the 10.1.2.2 gateway.
最新試題
Which of the following if addresses can be assigned to host devices?（）
Which Frame Relay feature is responsible for transmitting keepalives to ensure that the PVC does not shut down because of inactivity?（）
What does a configuration Register Setting of 0x2105 indicate to the Router? （）
A network host is configured as follows: Host IP address: 192.168.16.183 Subnet mask: 255.255.255.224 Default gateway: 192.168.16.190 Which of the following statements describe the network to which this host is attached?（）
What should the configuration register value be after successfully completing the password recover procedure and returning the router to normal operation? （）
Identify three valid host addresses in the 192.168.27.0 network with a subnet mask of 255.255.255.240. （）
You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?（）
An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location? （）
Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? （）
New switches have been purchased for a network upgrade. The objective for the network design emphasizes efficient, error-free transport instead of fast transport.Which switching mode should be configured on the new switches to provide error-free transport to the network? （）