A. If a packet is sent to a multicast group address, the multicast frame contains the source multicast address.
B. A router does not have to be a member of a multicast group to receive multicast data.
C. A router must be a member of a multicast group to send to the group.
D. A router does not have to be a member of a multicast group to send to the group.
E. If a packet is sent to a multicast group address, all members of the multicast group will rece ive it.
F. A router must be a member of a multicast group to receive multicast data.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. What two statements are true?（）
A. This is the designated router (DR) on the FastEthernet 0/0 link.
B. The output was generated by the show ip interface c ommand.
C. The router was configured with the commands:r outer ospf 1 network 172.16.6.0 0.0.0.255 area 1
D. The IP address of the backup designated router (BDR) is FE80::205:5FFF:FED3:5808.
E. Interface FastEthernet 0/0 was configured with the ipv6 o spf 1 area 1 command.
F. OSPF version 2 has been enabled to support IPv6.
A. 2001:0DB8:417A
B. 2001::0DB8::417A
C. 2001:::0DB8::417A
D. 2001:0D B8:0:0:417A
E. 2001::DB8:0:0:417A
F. 2001:::0DB8:0:0:417A
A. An IPv6 address is 128 bits long.
B. An IPv6 header contains the header checksum field.
C. An IPv6 header is 20 bits long.
D. An IPv6 header contains the next header field.
E. IPv6 route rs send RA messages.
F. An IPv6 header contains the protocol field.
A. OSPFv3 for IPv6 authen tication is supported by IPv6 IPsec.
B. OSPFv3 for IPv6 authentication is supported by MD5 authentication.
C. OSPFv3 for IPv6 authentication is supported by IPv4 IPsec.
D. OSPFv3 for IPv6 authentication is supported by SHA - 1 authentication.
A. ::/0 is the default route, and ::/128 is the unspecified address.
B. ::/0 is the unicast address, and ::/128 is the anycast address.
C. ::/0 is the anycast address, and ::/128 is the multicast address.
D. ::/0 is the unicast address, and ::/12 8 is the multicast address.
E. ::/0 is the unspecified address, and ::/128 is the multicast address.
F. ::/0 is the anycast address, and ::/128 is the default address.
最新試題
Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 1tunnel source loopback 1tunnel destination 192.168.1.2tunnel mode ipv6ip isatapipv6 address 2000::/64 eui - 64
The following output occurs on Router R1 , which runs both EIGRP for IPv6 and OSPFv3, with redistribution from EIGRP into OSPF configured with the redistribute eigrp 1 metric 25 command. Interface S0/0/1 has been enabled for EIGRP ASN 1. Which of the following should be true of redistribution in this case?（）D 2000::/64 [90/1422516]via FE80::213:19FF:FE7B:5026, Serial0/0/1C 2000:0:0:1::/64 [0/0]via Serial0/0/1, directly connectedL 2000::1:213:19FF:FE7B:5004/128 [0/0]via Serial0/0/1, receive
Look at the following configuration below and select the statements that are true.（）RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（）ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
An ISP has assigned prefix 3000:1234:5678::/48 to Company1. Which of the following terms would typically be used to describe this type of public IPv6 prefix?（）
Router R1 lists the following output from a show command. Which of the following is true about R1?（）R1# show ip v6 interface f0/0FastEthernet0/0 is up, line protocol is upIPv6 is enabled, link - local address is FE80::213:19FF:FE12:3456No Virtual link - local address(es):Global unicast address(es):2000::4:213:19FF:FE12:3456, subnet is 2000:0:0:4::/64 [EUI]Jo ined group address(es):FF02::1FF02::2FF02::1:FF:12:3456
Which of the following answers lists either a protocol or function that can be used by a host to dynamically learn its own IPv6 address?（）
Which of the following is the shortest valid abbreviation for FE80:0000:0000:0000:0010:0000:0000:0123?（）
The answers each list a tunnel method and two consecutive IPv6 address quartets.Which answers identify a tunneling method that relies on an IPv4 address to be embedded into an IPv6 address, within the correct quartets listed?（）