A. The multicast sources must register with the RP to form the multicast distribution tree.
B. An RP is required only in networks running Protocol Independent Multicast dense mode (PIM DM).
C. The multicast receivers must register with the RP to form the multicast distribution tree.
D. An RP is required only in networks running Protocol Independent Multicast sparse mode (PIM SM).
E. An RP is required only in networks running Protocol Independent Multicast sparse - dense mode (PIM - SDM).
F. To form the multicast distribution tree, the multicast sources register with and the receivers join the RP.
您可能感興趣的試卷
你可能感興趣的試題
A. 228.10.10.7
B. 229.11.10.7
C. 229.138.10.7
D. 229.138.10.8
E. 228.10.10.8
F. 228.10.138.7
A. 169.254.23.59
B. 223.254.255.254
C. 225.1.1.1
D. 227.43.34.2
E. 238.3.3.3
F. 249.1.2.3
A. acts as a meeting place for sources and receivers of multicast traffic
B. used in PIM dense m ode to create a database of all multicast sources
C. used in PIM dense and sparse mode to create a database of all multicast sources
D. acts as the designated router for a broadcast segment when multicast routing is enabled
Refer to the exhibit. IP multicast for group address 224.1.1.1 has been enabled on all router s in the network. Hosts on Network A receive the multicast traffic. However, hosts on Network B do not. On the basis of outputs provided, what could be the cause of the problem? （）
A. The route to 224.69.15.0/24 will be out Ethernet 0
B. The reverse path forwarding (RPF) for the route 224.2.0.1 failed to find the interface on which the multicast packet was rece ived
C. Multicast route to 224.69.15.0/24 was added to the mroute table and created by a source directly connected to the router
D. Multicast route to 10.16.0.0/16 was added to the mroute table and created by a source directly connected to the router
E. This router received an IGMP host report from a group member or a PIM join message
A. IGMP snooping and Cisco Group Membership Protocol (CGMP) can be used simultaneously on a switch.
B. IGMP snooping a nd Cisco Group Membership Protocol (CGMP) were developed to help Layer 3 switches make intelligent forwarding decisions on their own.
C. IGMP snooping examines IGMP join/leave messages so that multicast traffic is forwarded only to hosts that sent an IG MP message toward the router.
D. IGMP snooping is an IP multicast constraining mechanism for Layer 2 switches.
E. IGMP snooping is enabled with the ip multicast - routing global configuration command.
最新試題
A client host uses IPv4 to communicate with one ser ver and IPv6 to communicate with another.Which of the following IPv6 coexistence features is likely at work on the host?（）
Router R1 sits at an Enterprise branch office, using both the Internet and a leased line to another Enterprise router for its two connectivity options back into the rest of the Enterprise network. The engineer planning for this branch decided to use the leased line for all Enterprise traffic, unless it fails, in which case the Internet connection should be used to pass traffic to the Enterprise.Which of the following is most likely to be useful on the branch router?（）
The following output occurs on Router R1 , which runs both EIGRP for IPv6 and OSPFv3, with redistribution from EIGRP into OSPF configured with the redistribute eigrp 1 metric 25 command. Interface S0/0/1 has been enabled for EIGRP ASN 1. Which of the following should be true of redistribution in this case?（）D 2000::/64 [90/1422516]via FE80::213:19FF:FE7B:5026, Serial0/0/1C 2000:0:0:1::/64 [0/0]via Serial0/0/1, directly connectedL 2000::1:213:19FF:FE7B:5004/128 [0/0]via Serial0/0/1, receive
An Enterprise rou ter, Ent1, displays the following excerpt from the show ip bgp command. ENT1 has an eBGP connection to an ISP router with address 3.3.3.3 and an iBGP connection to a router with address 4.4.4.4. Which of the following is most likely to be true?（）Network Next Hop Metric LocPrf Weight Path*> 3.3.3.3 0 0 1 1 1 1 218 i
Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 1tunnel source loopback 1tunnel destination 192.168.1.2tunnel mode ipv6ip isatapipv6 address 2000::/64 eui - 64
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（）ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（）ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable
An engineer is reviewing another engineer's sample configuration for a GRE tunnel used to pass IPv6 traffiC. The tunnel ha s not yet been configured on the router.Which of the following commands is not required for the configuration to pass IPv6 traffic?（）
Which of the following answers lists either a protocol or function that can be used by a host to dynamically learn its own IPv6 address?（）