Refer to the exhibit. Which two conclusions can be drawn from the debug ip igmp output?()
A. The router sent an IGMP version 2 query out interface Ethernet1 at multicast address 224.0.0.1.
B. Router RTA received an IGMP report version 1 from host 192.168.9.1.
C. Reverse Path Forwarding (RPF) is ena bled for 192.168.9.4.
D. Reverse Path Forwarding (RPF) is enabled for 224.0.1.40.
E. The IP multicast groups are 224.0.0.1, 224.0.1.40, and 239.255.0.1.
F. IP PIM RP mapping is static.
您可能感興趣的試卷
你可能感興趣的試題
A. IGMP
B. IGMP snooping
C. PIM
D. CGMP
E. static assignment
F. CDP
A. Sparse mode multicast uses a pull model to send multicast traffic to where it is requested
B. Dense mode multicast uses a push model to flood traffic throughout the network and then prunes the unwanted traffic
C. Dense mode multicast requires explicit join messa ges from their members
D. Sparse mode uses reverse path forwarding (RPF) to prune off redundant flows
E. The primary use of sparse mode multicast is for test labs and router performance testing
A. The multicast sources must register with the RP to form the multicast distribution tree
B. An RP is required only in networks running Protocol Independent Multicast dense mode ( PIM DM)
C. The multicast receivers must register with the RP to form the multicast distribution tree
D. An RP is required only in networks running Protocol Independent Multicast sparse mode (PIM SM)
E. An RP is required only in networks running Pro tocol Independent Multicast sparse - dense mode (PIM - SDM)
F. To form the multicast distribution tree, the multicast sources register with and the receivers join the RP
Refer to the exhibit. All routers have Protocol Independent Multicast (PIM) enabled interfaces. On the basis of the configuration provided on routers R1 and R2, which router will take on the func tion of rendezvous point (RP) for the multicast network? ()
A. both routers R1 and R2
B. router R1
C. router R2
D. none of the routers since they are not configured with static RP
Refer to the network of Layer 3 switches in the exhibit. The RPI Multi cast Server only multicasts to hosts connected to multilayer switches 5 and 6. The CMU Multicast Server multicasts to hosts on multilayer switches 1 - 6. Given the number of configuration steps involved, what is the most efficient way to configure the net work while meeting the requirements for multicast data flow? ()
A. Configure each switch with PIM sparse mode and a separate instance of PIM dense mode.Specify switch 1 as the root for the RPI Multicast Server. Specify switch 2 as the root for the CMU Multicast Server.
B. Configure each switch with PIM sparse mode and a separate instance of PIM dense mode. Leave each multicast server as the root of its own multicast tree.
C. Configure each switch with PIM sparse - dense mode. Configure switch 3 as a ren dezvous point for the RPI multicast stream.
D. Configure each switch with PIM sparse mode and a separate instance of PIM dense mode.Allow the switches to elect their own root for each multicast tree.
E. Configure each switch with PIM sparse mode.
F. Configure each switch with PIM dense mode.
最新試題
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?()interface f0/0ipv6 address 2345:0:0:8::1/64
The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer?()interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?()ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1
Which of the following answers lists either a protocol or function that can be used by a host to dynamically learn its own IPv6 address?()
Which of the following are true of both OSPFv2 and OSPFv3?()
Router R1 sits at an Enterprise branch office, using the Internet for its only connectivity back to the rest of the EnterprisE.Which of the following is not a ben efit of using an IPsec tunnel for packets sent through the Internet, between R1 and the rest of the Enterprise?()
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?()ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?()
Which of the following is the shortest valid abbreviation for FE80:0000:0000:0000:0010:0000:0000:0123?()
An ISP has assigned prefix 3000:1234:5678::/48 to Company1. Which of the following terms would typically be used to describe this type of public IPv6 prefix?()