To protect against first-hop router failure， four protocols were developed to ensure IP routing redundancy.
Which of the following are they？（）
A. HSRP
B. IRDP
C. ICMP
D. VRRP
E. MSTP
F. GLBP
您可能感興趣的試卷
你可能感興趣的試題
HSRP is being set up between two Company devices.
In what three states is it possible for an HSRP router to be in？（）
A. Standby
B. Established
C. Active
D. Idle
E. Backup
F. Init
R1 and R2 exchange HSRP between each other in the Company network.
In which three HSRP states do routers send hello messages？（）
A. Learn
B. Speak
C. Standby
D. Listen
E. Active
F. Remove
You need to implement a high availability design in the Company routed network.
Which protocol allows for the automatic selection and simultaneous use of multiple available gateways as well as automatic failover between those gateways？（）
A. VRRP
B. GLBP
C. IRDP
D. HSRP
E. None of the other alternatives apply
You need to decide on the best router redundancy protocol to use in the Company network.
Which two statements are true about HSRP， VRRP， and GLBP？（）
A. GLBP and VRRP allow for MD5 authentication， whereas HSRP does not.
B. HSRP allows for multiple upstream active links being simultaneously used， whereas GLBP does not.
C. GLBP allows for router load balancing of traffic from a network segment without the different host IP configurations required to achieve the same results with HSRP.
D. Unlike HSRP and VRRP， GLBP allows automatic selection and simultaneous use of multiple available gateways.
E. GLBP allows for router load balancing of traffic from a network segment by utilizing the creation of multiple standby groups.
Routers R1 and R2 use HSRP so that one router will back up the other should there be a failure.
Which two statements are true about the Hot Standby Router Protocol （HSRP）？ （）
A. Load sharing with HSRP is achieved by creating multiple subinterfaces on the HSRP routers.
B. Routers configured for HSRP can belong to multiple groups and multiple VLANs.
C. Load sharing with HSRP is achieved by creating HSRP groups on the HSRP routers.
D. All routers configured for HSRP load balancing must be configured with the same priority.
E. Routers configured for HSRP must belong to only one group per HSRP interface.
最新試題
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Refer to the exhibit. Which Virtual Router Redundancy Protocol （VRRP） statement is true about the roles of the master virtual router and the backup virtual router？（）
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain， the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change？（）
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this？（）
Refer to the exhibit. Based on the output of the show spanning-tree command， which statement is true？ （）
Which statement is correct about RSTP port roles？（）
What is the configured priority value of the Vlan105’s group on DS2 ？（）
What two things will occur when an edge port receives a BPDU？（）
During routine maintenance， it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time， DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ？ （）