Examine the router output above. Which two items are correct？（）
A. The local IP address of Router A is 10.1.0.6.
B. The local IP address of Router A is 10.1.0.20.
C. If Ethernet 0/2 goesdown， the standby router will take over.
D. When Ethernet 0/3 of RouterA comes back up， the priority will become 105.
E. Router A will assume the active state if its priority is the highest.
您可能感興趣的試卷
你可能感興趣的試題
What can be determined about the HSRP relationship from the displayed debug output？ （）
A. Router 172.16.11.112 will be the active router because its HSRP priority is preferred over router 172.16.11.111.
B. Router 172.16.11.111 will be the active router because its HSRP priority is preferred over router 172.16.11.112.
C. The IP address 172.16.11.111 is the virtual HSRP router IP address.
D. The IP address 172.16.11.112 is the virtual HSRP router IP address.
E. The nonpreempt feature is enabled on the 172.16.11.112 router.
F. The preempt feature is not enabled on the 172.16.11.111 router.
Refer to the exhibit. Based upon the debug output that is shown，
which three statements about HSRP are true？（）
A. The router with IP address 172.16.11.111 haspreempt configured.
B. The final active router is the router with IP address 172.16.11.111.
C. The router with IP address 172.16.11.112 has nonpreempt configured.
D. The priority of the router with IP address 172.16.11.112 is preferred over the router with IP address 172.16.11.111.
E. The router with IP address 172.16.11.112 is using default HSRP priority.
F. The IP address 172.16.11.115 is the virtual HSRP IP address.
A. independent of SSO
B. NSF combined with SSO enables supervisor engine load balancing
C. supported by RIPv2， OSPF， IS-IS， and EIGRP
D. supports IPv4 and IPv6 multicast
E. prevents route flapping
F. dependent on FIB tables
pany has a Catalyst 6500 and you need to configure redundancy between the supervisor modules. With route processor redundancy （RPR+）， the redundant supervisor engine is fully initialized and configured， which shortens the switchover time if the active supervisor engine fails.
Which three statements are true about the RPR + operations when the redundant supervisor engine switched over the failed primary supervisor engine？ （）
A. Static IP routes are maintained across a switchover because they are configured from entries in the configuration file.
B. Information about dynamic routing states， maintained on the active supervisor engine， is synchronized to the redundant supervisor engine and is transferred during the switchover.
C. Information about dynamic routing states， maintained on the active supervisor engine， is not synchronized to the redundant supervisor engine and is lost on switchover.
D. The Forwarding Information Base （FIB） tables are cleared on a switchover. As a result， routed traffic is interrupted until route tables reconverge.
E. Static IP routes are cleared across a switchover and recreated from entries in the configuration file on the redundant supervisor engine.
F. The Forwarding Information Base （FIB） tables are maintained during the switchover. As a result， routed traffic continues without any interruption when the failover occurs.
Refer to the exhibit.
What is the result of setting GLBP weighting at 105 with lower threshold 90 and upper threshold 100？ （）
A. Only if both tracked objects are up will this router will be available as an AVF for group 1.
B. Only if the state of both tracked objects goes down will this router release its status as an AVF for group 1.
C. If both tracked objects go down and then one comes up， but the other remains down， this router will be available as an AVF for group 1.
D. This configuration is incorrect and will not have any effect on GLBP operation.
E. If the state of one tracked object goes down then this router will release its status as an AVF for group 1.
最新試題
Which router redundancy protocol cannot be configured for interface tracking？（）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain， the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change？（）
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statements about the STP process for VLAN 200 are true？ （）
Which two statements about the various implementations of STP are true？（）
Which statement is correct about RSTP port roles？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link？（）
How are STP timers and state transitions affected when a topology change occurs in an STP environment？（）
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）