A. RIP
B. BGP
C. IS - IS
D. OSPF
E. EIGRP
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. Routers R1 and R2 have been configured to operate with OSPF. Routers R1 and R3 have been configured to operate with RIP. After configuring the redistribution between OSPF a nd RIP on R1, no OSPF routes are distributed into RIP. What should be done to correct this problem? （）
A. The redistribution command should be reentered with the match route - type parameter included.
B. The redistribution command should be reentered wit h the route - map map - tag parameter included.
C. The redistribution command should be reentered with the metric metric - value parameter included.
D. Routes will first need to be distributed into another protocol, and then into RIP.
Refer to the exhibit. What is required to complete the IPv6 routing configurations shown?（）
A. Interface authentication must be configured
B. The routing processes must be configured with an area ID
C. IP unicast routing must be enabled
D. IPv4 ad dresses must be applied to the interfaces
Refer to the parti al configurations in the exhibit. What address is utilized for DR and BDR identification on Router1?（）
A. the serial 1/1 address
B. the serial 2/0 address
C. a randomly generated internal address
D. the configured router - id address
A.Interfaces have a default metric of 1.
B.Level 1 is intra - area and level 2 is interarea.
C.Level 1 routing is between an end system (ES) and IS while Level 2 routing is between an IS and IS.
D. Hosts send ISHs while routers send ESHs.
E. IS - IS is an open standard.
F. Metrics depend on interface speed.
Intermediate system to intermediate system (IS - IS), is a protocol used by network devices (routers) to determine the best way to forward datagrams through a packet - switched network, a process called routing. Which three attributes are of the IS - IS routing protocol? （）
A. supports VLSM
B. link - state routing protocol
C. operati on is similar to BGP
D. supports two routing levels within an autonomous system
最新試題
Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?（）interface f0/0mac - address 1111.1111.1 111ipv6 address 2000::/64 eui - 64ipv6 address 2001::1/64
A client host uses IPv4 to communicate with one ser ver and IPv6 to communicate with another.Which of the following IPv6 coexistence features is likely at work on the host?（）
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
Which of the following are true of both OSPFv2 and OSPFv3?（）
The answers each list a tunnel method and two consecutive IPv6 address quartets.Which answers identify a tunneling method that relies on an IPv4 address to be embedded into an IPv6 address, within the correct quartets listed?（）
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output？（）B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18
An Enterprise rou ter, Ent1, displays the following excerpt from the show ip bgp command. ENT1 has an eBGP connection to an ISP router with address 3.3.3.3 and an iBGP connection to a router with address 4.4.4.4. Which of the following is most likely to be true?（）Network Next Hop Metric LocPrf Weight Path*> 3.3.3.3 0 0 1 1 1 1 218 i
Look at the following configuration below and select the statements that are true.（）RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0
Which of the following answers lists either a protocol or function that can be used by a host to dynamically learn its own IPv6 address?（）