A.enables PortFast
B.disables trunking
C.disables Cisco Discovery Protocol
D.enables port security
E.enables loopguard
F.disables EtherChannel
您可能感興趣的試卷
你可能感興趣的試題
You are implementing basic switch security best practices.
Which of these is a tactic that you can use to mitigate compromises from being launched through the switch？（）
A.Make all ports private VLAN ports.
B.Place all unused ports in native VLAN 1 until needed.
C.Proactively configure unused switch ports as access ports.
D.Disable Cisco Discovery Protocol globally.
Three Cisco Catalyst switches have been configured with a first-hop redundancy protocol. While reviewing some show commands， debug output， and the syslog， you discover the following information：
What conclusion can you infer from this information？（）
A.VRRP is initializing and operating correctly.
B.HSRP is not properly exchanging three hello messages.
C.VRRP is not properly exchanging three hello messages.
D.HSRP is initializing and operating correctly.
E.GLBP is not properly exchanging three hello messages.
F.GLBP is initializing and operating correctly.
You work as a network engineer for . You study the exhibit carefully. Three switches are configured for HSRP. Switch1 remains in the HSRP listen state.
What is the most likely cause of this status？（）
A.this is normal operation
B.IP addressing is incorrect
C.standby group number does not match VLAN number
D.incorrect standby timers
E.incorrect priority commands
hostname Switch1
interface Vlan10
ip address 172.16.10.32 255.255.255.0
no ip redirects
standby 1 ip 172.16.10.110
standby 1 timers 1 5
standby 1 priority 130
hostname Switch2
interface Vlan10
ip address 172.16.10.33 255.255.255.0
no ip redirects
standby 1 ip 172.16.10.110
standby 1 timers 1 5
standby 1 priority 120
HSRP was implemented and configured on two switches while scheduled network maintenance was performed.
After the two switches have finished rebooting， you notice via show commands that Switch2 is the HSRP active router.
Which two items are most likely the cause of Switch1 not becoming the active router？ （）
A.premption is disabled
B.standby group number does not match VLAN number
C.IP addressing is incorrect
D.IP redirect is disabled
E.incorrect standby timers
F.booting delays
You work as a network engineer for . You study the exhibit carefully. From the configuration shown，
what can be determined？（）
Exhibit:
A.The remaining secure MAC addresses will be dynamically learned， converted to sticky secure MAC addresses， and added to the running configuration.
B.Since a voice VLAN is configured in this example， port security should be set for a maximum of 2.
C.The sticky addresses will only be those manually configured MAC addresses enabled with the sticky keyword.
D.A security violation will restrict the number of addresses to a maximum of 10 addresses per access VLAN and voice VLAN. The port will be shut down if more than 10 devices per VLAN attempt to access the port.
最新試題
Which two statements are true about BPDU port-guard and BPDU filtering？（）
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link？（）
Which two statements about the various implementations of STP are true？（）
If G1/0/1 on DS1 is shutdown， what will be the current priority value of the Vlan105’s group on DS1 ？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Which two statements are true when the extended system ID feature is enabled？ （）
Refer to the exhibit. For what purpose is the command show ip cef used？（）
How are STP timers and state transitions affected when a topology change occurs in an STP environment？（）
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statements about the STP process for VLAN 200 are true？ （）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）