You work as a network engineer for. You study the exhibit carefully. You have configured an interface to be an SVI for Layer 3 routing capabilities. Assuming that all VLANs have been correctly configured and based on the configuration example shown，
what can be determined？ （）
Exhibit：
A.Interface gigabitethernet0/2 will be excluded from Layer 2 switching and enabled for Layer 3 routing.
B.The interface is missing IP configuration parameters； therefore， it will only function at Layer 2.
C.The command switchport autostate exclude should be entered in global configuration mode， not sub-interface mode， to enable a Layer 2 port to be configured for Layer 3 routing.
D.The configured port is excluded in the calculation of the status of the SVI.
您可能感興趣的試卷
你可能感興趣的試題
You have configured a Cisco Catalyst switch to perform Layer 3 routing via an SVI and have
assigned that interface to VLAN 20. To check the status of the SVI， you issue the show interfaces vlan 20 command at the CLI prompt. You see from the output display that the interface is in an "up/up" state.
What must be true in an SVI configuration to bring the VLAN and line protocol up？（）
A.The port must be physically connected to another Layer 3 device.
B.At least one port in VLAN 20 must be active.
C.The Layer 3 routing protocol must be operational and receiving routing updates from neighboring peer devices.
D.Because this is a virtual interface， the operational status will always be in an "up/up" state.
A.The best match of the ACL entries will be used for granularity of control.
B.They use source IP information for matching operations.
C.They use source and destination IP information for matching operations.
D.They use source IP information along with protocol-type information for finer granularity of control.
A.Enable the switch to participate in routing updates from external devices with the router command in global configuration mode.
B.Enter the no switchport command to disable Layer 2 functionality at the interface level.
C.Each port participating in routing of Layer 3 packets must have an IP routing protocol assigned on aperinterface level.
D.Routing is enabled by default on a multilayer switch， so the port can become a Layer 3 routing interface by assigning the appropriate IP address and subnet information.
A.ease of IP address assignment versus use of external routers
B.redundancy from trunking between distribution layer switches
C.provides first-hop redundancy to clients
D.allows inter-VLAN communication without requiring complexity of routing protocols
You work as a network engineer for . You study the exhibit carefully.
What best describes the Cisco IOS IP SLA command and output in the exhibit？（）
A.verifies which operation types have been enabled for IP SLA source
B.verifies which operation types have been enabled for IP SLA responder
C.verifies which operation types are supported in software
D.verifies enabled operation types that are not running
最新試題
Refer to the exhibit. Which statement is true about the output？（）
Refer to the exhibit. What will happen when one more user is connected to interface FastEthernet 5/1？ （）
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link？（）
Which two statements about the various implementations of STP are true？（）
Which two statements are true when the extended system ID feature is enabled？ （）
How are STP timers and state transitions affected when a topology change occurs in an STP environment？（）
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain， the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change？（）