A.Configuration changes made on the port-channel interface apply to all physical ports assigned to the portchannel interface.
B.Configuration changes made on a physical port that is a member of a port-channel interface apply to the port-channel interface.
C.Configuration changes are not permitted with Port Aggregation Protocol； instead， the standardized Link Aggregation Control Protocol should be used if configuration changes are required.
D.The physical port must first be disassociated from the port-channel interface before any configuration changes can be made.
您可能感興趣的試卷
你可能感興趣的試題
A.no switchport trunk native vlan vlan-id
B.switchport nonegotiate
C.no switchport mode dynamic desirable
D.switchport mode access
A.switchport dynamic auto switchport dynamic auto
B.switchport access vlan 10 switchport mode dynamic desireable
C.switchport mode trunk switchport nonegotiate
D.Leave both ports with the default trunk settings
A.By default， native VLAN packets going out this port will be tagged.
B.Without an encapsulation command， 802.1Q will be the default encapsulation if DTP fails to negotiate a trunking protocol.
C.The interface will support the reception of tagged and untagged traffic.
D.If the device connected to this port is not 802.1Q-enabled， it will not be able to handle 802.1Q packets.
A.PortFast， UplinkFast， and BackboneFast specific configurations are ignored in Rapid PVST mode.
B.RSTP is enabled globally and uses existing STP configuration.
C.Root and alternative ports transition immediately to the forwarding state.
D.Convergence is improved by using sub-second timers for the blocking， listening， learning， and forwarding port states.
A.Unidirectional link detection is achieved through monitoring STP BPDUs.
B.It is recommended that it be enabled globally rather than on an individual port.
C.When an error is detected， normal mode will disable a port.
D.It is recommended that it be enabled in normal mode.
E.It is recommended that it be used with the loop guard feature.
最新試題
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this？（）
Which three statements are true of the Link Aggregation Control Protocol （LACP）？（）
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ？ （）
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statements about the STP process for VLAN 200 are true？ （）
What two things will occur when an edge port receives a BPDU？（）
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain， the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change？（）
Which two statements are true when the extended system ID feature is enabled？ （）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）