A. L1 ES
B. L2 IS
C. L2 ES
D. L1 IS
E. L1/L2 IS
您可能感興趣的試卷
你可能感興趣的試題
A. IS - IS is more CPU - intensive than is OSPF
B. For greater fine tuning there are more IS - IS timers
C. IS - IS LSP con tains TLV fields and OSPF LSU contains the LSAs
D. New additions to the protocol are easily implemented in OSPF but not with IS - IS
E. OSPF has more area types than does IS - IS
A. uses a default IOS metric of 10 on each interface
B. uses an on - demand circuit to reduce the hello and LSA flooding across switched WAN li nks,such as ISDN
C. uses a DIS and a backup DIS to present the psuedo - node on the LAN
D. encapsulates PDUs directly into a data - link frame
E. uses stubby areas to improve network scalability
F. runs PRC (Partial Route Calculations) to calculate IP re achability information
A. BGP requires redundant TCP sessions between iBGP peers.
B. Routes learned via eBGP are never propagated to other iBGP peers.
C. A full mesh allows for optimal routing within the Transit AS.
D. Routes learned via iBGP are never propagated to other eBGP peers.
E. Routes learned via iBGP are never propagated t o other iBGP peers.
Given the network diagram, which address would successfully summarize only the networks seen? （）
A. 192.168.0.0/24
B . 192.168.8.0/20
C. 192.168.8.0/21
D. 192.168.12.0/20
E. 192.168.16.0/21
F. These networks cannot be summarized.
A. EIGRP
B. RIP
C. OSPF
D. IS - IS
最新試題
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（）ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output？（）B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18
Which of the following answers lists a multicast IPv6 address?（）
An Enterprise rou ter, Ent1, displays the following excerpt from the show ip bgp command. ENT1 has an eBGP connection to an ISP router with address 3.3.3.3 and an iBGP connection to a router with address 4.4.4.4. Which of the following is most likely to be true?（）Network Next Hop Metric LocPrf Weight Path*> 3.3.3.3 0 0 1 1 1 1 218 i
A client host uses IPv4 to communicate with one ser ver and IPv6 to communicate with another.Which of the following IPv6 coexistence features is likely at work on the host?（）
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, and into the core of an Enterprise network. The branch also allows local hosts to communicate directly with public sites in th e Internet over this same DSL connection.Which of the following answers defines how the branch NAT config avoids performing NAT for the Enterprise directed traffic but does perform NAT for the Internet - directed traffic?（）
Router R1 sits at an Enterprise branch office, using both the Internet and a leased line to another Enterprise router for its two connectivity options back into the rest of the Enterprise network. The engineer planning for this branch decided to use the leased line for all Enterprise traffic, unless it fails, in which case the Internet connection should be used to pass traffic to the Enterprise.Which of the following is most likely to be useful on the branch router?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）
The answers each list a tunnel method and two consecutive IPv6 address quartets.Which answers identify a tunneling method that relies on an IPv4 address to be embedded into an IPv6 address, within the correct quartets listed?（）