Router R1 has been configured for EIGRP. The configuratio n also includes an ACL with one line -access - list 1 permit 10.100.32.0 0.0.15.255 - and the EIGRP configuration includes the distribute -list 1 in command.
Which of the following routes could not be displayed in the output of the show ip eigrp topology comm and as a result?（）
A. 10.10.32.0/19
B. 10.10.44.0/22
C. 10.10.40.96/27
D. 10.10.48.0/23
E. 10.10.60.0/30
您可能感興趣的試卷
你可能感興趣的試題
Router R1 lists 4 routes for subnet 10.1.1.0/24 in the output of the show ip eigrp topology all - links command. The variance 200 command is configured, but no other related commands are configured. Which of the following rules are true regarding R1's decision of what r outes to add to the IP routing table?
Note that RD refers to reported distance and FD to feasible distanc E.（）
A. Adds all routes for which the metric is <= 200 * the best metric among all routes
B. Adds all routes because of the ridiculously high variance setting
C. Adds all successor and feasible successor routes
D. Adds all successor and feasible successor routes for which the metric is<=200 * the best metric among all routes
A network design shows that R1 has four different possible paths from itself to the Data Center subnets.
Which one of the following commands is most likely to show you all the possible next - hop IP addresses for these four possible routes?（）
A. show ip eigrp topology
B. show ip eigrp topology all - links
C. show ip route eigrp
D. show ip route eigrp all - links
E. show ip eigrp topology all - learned
A company has a Frame Relay WAN with one central - site router and 100 branch office routers. A partial mesh of PVCs exists: one PVC between the central site and each of the 100 branch routers.
Which of the following could be true about the number of EIGRP neighbor ships?（）
A. A partial mesh totaling 100: one between the central - site router and each of the 100 branches.
B. A full mesh - (101 * 100) / 2 = 5050 - One neighborship between each pair of routers.
C. 101 - One between each router (including the central site) a nd its nearby PE router.
D. None of the answers is correct.
Refer to the exhibit. Which two statements are true about the partial configuration that is shown? （）
A. The first DHCP client to connect to the FastEthernet 0/1 interface will receive the IP address 10.10.0.1.
B. DHCP requests received on the FastEthernet 0/1 interface will be forwarded to 10.0.0.2.
C. The first DHCP client to connect to the FastEthernet 0/0 interface will receive the IP a ddress 10.0.0.1
D. The first DHCP client to connect to the FastEthernet 0/0 interface will receive the IP address 10.0.0.6.
E. Hosts connected to the FastEthernet0/1 interface will not receive DHCP replies from the router.
A. BOOTP
B. TFTP
C. ARP
D. DNS
E. proxy - ARP
F. FTP
最新試題
Which of the following is helpful to allow an IPv6 host to learn the IP address of a default gateway on its subnet?（）
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?（）
The answers each list a tunnel method and two consecutive IPv6 address quartets.Which answers identify a tunneling method that relies on an IPv4 address to be embedded into an IPv6 address, within the correct quartets listed?（）
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, and into the core of an Enterprise network. The branch also allows local hosts to communicate directly with public sites in th e Internet over this same DSL connection.Which of the following answers defines how the branch NAT config avoids performing NAT for the Enterprise directed traffic but does perform NAT for the Internet - directed traffic?（）
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output？（）B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（）ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network.Which of the following answers best describes the router's logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?（）
The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer？（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1
The following output on Router R1 lists details of a BGP route for 190.1.0.0/16. Which of the following is true based on this output?（）R1# show ip bgp 19 0.1.0.0/16BGP routing table entry for 190.1.0.0/16, version 121Paths: (1 available, best #1, table Default - IP - Routing - Table)Advertised to update - groups:11 2 3 41.1.1.1 from 2.2.2.2 (3.3.3.3)Origin IGP, metric 0, localpref 100, valid, internal, best
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0