Refer to the exhibit.
What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
A.ip routing
B.no ip routing
C.router eigrp 1
D.no router eigrp 1
E.mls qos
F.no mls qos
您可能感興趣的試卷
你可能感興趣的試題
A.VLAN instance mapping and revision number
B.VLAN instance mapping and member list
C.VLAN instance mapping， revision number， and member list
D.VLAN instance mapping， revision number， member list， and timers
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct，
what will be true about Switch 15？（）
A.All ports will be in forwarding mode.
B.All ports in VLAN 10 will be in forwarding mode.
C.All ports in VLAN 10 will be in forwarding mode and all ports in VLAN 20 will be in blocking mode.
D.All ports in VLAN 10 will be in forwarding mode and all ports in VLAN 20 will be in standby mode.
A.BPDU port-guard can be enabled globally， whereas BPDU filtering must be enabled on a per-interface basis.
B.When globally enabled， BPDU port-guard and BPDU filtering apply only to PortFast enabled ports.
C.When globally enabled， BPDU port-guard and BPDU filtering apply only to trunking-enabled ports.
D.When a BPDU is received on a BPDU port-guard enabled port， the interface goes into the err-disabled state.
E.When a BPDU is received on a BPDU filtering enabled port， the interface goes into the err-disabled state.
F.When a BPDU is received on a BPDU filtering enabled port， the interface goes into the STP blocking state.
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：
00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）.
What would be the possible outcome of the problem？（）
A.The root port on switch SW_A will automatically transition to full-duplex mode.
B.The root port on switch SW_B will fallback to full-duplex mode.
C.The interfaces between switches SW_A and SW_B will transition to a blocking state.
D.Interface Fa 0/6 on switch SW_B will transition to a forwarding state and create a bridging loop.
A.mon Spanning Tree maintains a separate spanning-tree instance for each VLAN configured in the network.
B.The Spanning Tree Protocol （STP） is an evolution of the IEEE 802.1w standard.
C.Per-VLAN Spanning Tree （PVST） supports 802.1Q trunking.
D.Per-VLAN Spanning Tree Plus（PVST+） is an enhancement to 802.1Q specification and is supported only on Cisco devices.
E.Rapid Spanning Tree Protocol （RSTP） includes features equivalent to Cisco PortFast， UplinkFast， and BackboneFast for faster network reconvergence.
F.Multiple Spanning Tree （MST） assumes one spanning-tree instance for the entire Layer 2 network， regardless of the multiple number of VLANs
最新試題
Refer to the exhibit. All network links are FastEthernet. Although there is complete connectivity throughout the network， Front Line users have been complaining that they experience slower network performance when accessing the server farm than the Reception office experiences. Based on the exhibit， which two statements are true？（）
If G1/0/1 on DS1 is shutdown， what will be the current priority value of the Vlan105’s group on DS1 ？（）
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）
Refer to the exhibit. Which Virtual Router Redundancy Protocol （VRRP） statement is true about the roles of the master virtual router and the backup virtual router？（）
Which three statements about STP timers are true？（）
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statements about the STP process for VLAN 200 are true？ （）
What is the configured priority value of the Vlan105’s group on DS2 ？（）
Which router redundancy protocol cannot be configured for interface tracking？（）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ？ （）