The following command output was gathered from Router R1, an ABR between areas 0 (backbone) and area 1. In this internetwork, area 0 contains all the subnets of cla ss A network 10.0.0.0. R1's OSPF process has a distribute - list prefix question in command configured. Assuming the subnets listed in the answers actually exist in area 0.
Which of the following occurs on router R1?（）
R1#sh ip prefix - list
ip prefix - list question: 4 entries
seq 5 deny 10.1.2.0/24 ge 25 le 27
seq 15 deny 10.2.0.0/16 ge 30 le 30
seq 20 permit 0.0.0.0/0 le 32
A. R1 will not create/flood a type 3 LSA for subnet 10.1.2.0/26 into area 1
B. R1 will not create/flood a Type 3 LSA for subnet 1 0.1.2.0/24 into area 1
C. R1 will not have an OSPF route for subnet 10.1.2.0/26 in its IP routing tablE
D. R1 will not have an OSPF route for subnet 10.1.2.0/24 in its IP routing tablE
您可能感興趣的試卷
你可能感興趣的試題
Router B1, an internal router in area 1, displays the following output. The only two ABRs connected to area 1 are performing Type 3 LSA filterinG. Which of the following answers is true based on the information in the output from B1?（）
R1# show ip route 10.1.0.0 255.255.0.0 longer - prefixes
! Legend lines omitted for brevity
10.0.0.0/8 is variably subnetted, 17 subnets, 3 masks
O 10.1.2.0/24 [110/658] via 10.10.13.1, 00:00:32, Serial0/0/0.1
O IA 10.1.1.0/24 [110/658] via 10.10.23.2, 00:41:39, Ser ial0/0/0.2
O IA 10.1.3.0/24 [110/658] via 10.10.23.2, 00:41:39, Serial0/0/0.2
A. A Type 3 LSA for 10.2.2.0/24 was filtered by both ABRs
B. A Type 3 LSA for 10.1.2.0/24 was not filtered by both ABRs
C. A Type 3 LSA for 10.1.3.0/24 was not filtered by at least one ABR
D. A Type 3 LSA for 10.1.1.0/24 filtered by both ABRs
Which of the following LSA types describe information related to topology or subnets useful for calculating routes for subnets inside the OSPF domain?（）
A. 1
B. 2
C. 3
D. 4
E. 5
F. 7
The following output was taken from Router R3. A scan of R3's configuration shows that no bandwidth commands have been configured in this router. Which of the following answers lists configuration settings could be a part of a configuration tha t results in the following output?（）
R3#show ip ospf interface brief
Interface PID Area IP Address/Mask Cost State Nbrs F/C
Se0/0/0.2 3 34 10.10.23.3/29 647 P2P 1/1
Se0/0/0.1 3 34 10.10.13.3/29 1000 P2P 1/1
Fa0/0 3 34 10.10.34.3/24 20 BDR 1/1
A. An a uto - cost reference - bandwidth 1000 command in router ospf mode
B. An auto - cost reference - bandwidth 2000 command in router ospf mode
C. An ip ospf cost 1000 interface S0/0/0.1 command in router ospf mode
D. An auto - cost reference - bandwidth 64700 command i n router ospf mode
Which of the following LSA types describes topology information that, when changed, requires a router in the same area to perform an SPF calculation?（）
A. 1
B. 2
C. 3
D. 4
E. 5
F. 7
R1 is internal to area 1, and R2 is internal to area 2. Subnet 10.1.1.0/24 exists in area 2 as a connected subnet off R2. ABR ABR1 connects area 1 to backbone area 0, and ABR2 c onnects area 0 to area 2.
Which of the following LSAs must R1 use when calculating R1's best route for 10.1.1.0/24?（）
A. R2's Type 1 LSA
B. Subnet 10.1.1.0/24's Type 2 LSA
C. ABR1's Type 1 LSA in area 0
D. Subnet 10.1.1.0/24's Type 3 LSA in Area 0
E. Subnet 10.1.1.0/24's Type 3 LSA in Area 1
最新試題
The following output on Router R1 lists details of a BGP route for 190.1.0.0/16. Which of the following is true based on this output?（）R1# show ip bgp 19 0.1.0.0/16BGP routing table entry for 190.1.0.0/16, version 121Paths: (1 available, best #1, table Default - IP - Routing - Table)Advertised to update - groups:11 2 3 41.1.1.1 from 2.2.2.2 (3.3.3.3)Origin IGP, metric 0, localpref 100, valid, internal, best
Look at the following configuration below and select the statements that are true.（）RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0
Router R1 sits at an Enterprise branch office, using the Internet for its only connectivity back to the rest of the EnterprisE.Which of the following is not a ben efit of using an IPsec tunnel for packets sent through the Internet, between R1 and the rest of the Enterprise?（）
The following output occurs on Router R1 , which runs both EIGRP for IPv6 and OSPFv3, with redistribution from EIGRP into OSPF configured with the redistribute eigrp 1 metric 25 command. Interface S0/0/1 has been enabled for EIGRP ASN 1. Which of the following should be true of redistribution in this case?（）D 2000::/64 [90/1422516]via FE80::213:19FF:FE7B:5026, Serial0/0/1C 2000:0:0:1::/64 [0/0]via Serial0/0/1, directly connectedL 2000::1:213:19FF:FE7B:5004/128 [0/0]via Serial0/0/1, receive
The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer？（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1
Router R1 lists the following output from a show command. Which of the following is true about R1?（）R1# show ip v6 interface f0/0FastEthernet0/0 is up, line protocol is upIPv6 is enabled, link - local address is FE80::213:19FF:FE12:3456No Virtual link - local address(es):Global unicast address(es):2000::4:213:19FF:FE12:3456, subnet is 2000:0:0:4::/64 [EUI]Jo ined group address(es):FF02::1FF02::2FF02::1:FF:12:3456
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（）ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1
An ISP has assigned prefix 3000:1234:5678::/48 to Company1. Which of the following terms would typically be used to describe this type of public IPv6 prefix?（）
Which of the following answers lists either a protocol or function that can be used by a host to dynamically learn its own IPv6 address?（）
An engineer is trying to summarize the following networks using the "ip summary- address eigrp"command:10.8.88.0/2510.8.89.48/2910.8.64.96/27Which network and subnet mask below would be the smallest EIGRP summary address to include all three subnets?（）