An enterprise has plans to start adding IPv6 support. The initial deployment requires support from some IPv6 - only device s that need to access servers that support only IPv4.
Which of the following tools would be most appropriate?（）
A. Native IPv6
B. Point - to -point tunnels
C. Multipoint tunnels
D. NAT - PT
您可能感興趣的試卷
你可能感興趣的試題
An enterprise h as plans to start adding IPv6 support. For the first year, the IPv6 will be in small pockets spread around the existing large IPv4 network, with occasional IPv6 traffic while applications teams test IPv6 - enabled servers and applications.
Which of the fol lowing tools would be most appropriate?（）
A. Native IPv6
B. Point - to -point tunnels
C. Multipoint tunnels
D. NAT - PT
A. Metric
B. Administrative distance
C. Timeout (seconds)
D. Prefix length
E. Interface ID
The following output occurs on Router R1 , which runs both EIGRP for IPv6 and OSPFv3, with redistribution from EIGRP into OSPF configured with the redistribute eigrp 1 metric 25 command. Interface S0/0/1 has been enabled for EIGRP ASN 1. Which of the following should be true of redistribution in this case?（）
D 2000::/64 [90/1422516]
via FE80::213:19FF:FE7B:5026, Serial0/0/
1
C 2000:0:0:1::/64 [0/0]
via Serial0/0/1, directly connected
L 2000::1:213:19FF:FE7B:5004/128 [0/0]
via Serial0/0/1, receive
A. Route 2000::/64 will be redistributed.
B. Route 2 000:0:0:1::/64 will be redistributed.
C. Route 2000:1:213:19FF:FE7B:5004/128 will be redistributed.
D. No routes will be redistributed because of the omission of the subnets parameter of the redistribute command.
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）
ipv6 router ospf 1
ipv6 unicast- routing
interface f0/0
ipv6 address 2000 ::1/64
ipv6 ospf 1 area 1
interface s0/0/0
ipv6 address 2001::/64 eui - 64
ipv6 ospf 1 area 0
A. OSPF works on F0/0 and S0/0/0 without further configuration
B. OSPF works with the addition of one command: a no shutdown command in OSPF router configur ation modE
C. OSPF works with the addition of one command: an router - id command in OSPF router configuration modE
D. OSPFv3 needs at least two more configuration commands before it works on R1
A. The method of choosing an OSPF router ID
B. Verification checks that must be validated before two routers can become OSPF neighbors
C. Support for route tags
D. Support for multiple instances per inter face
最新試題
Router R1 sits at an Enterprise branch office, using the Internet for its only connectivity back to the rest of the EnterprisE.Which of the following is not a ben efit of using an IPsec tunnel for packets sent through the Internet, between R1 and the rest of the Enterprise?（）
Which of the following is helpful to allow an IPv6 host to learn the IP address of a default gateway on its subnet?（）
Which of the following are true of both OSPFv2 and OSPFv3?（）
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network.Which of the following answers best describes the router's logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（）ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable
Which of the following features work the same in both RIP- 2 and RIPng?（）
Which of the following must match for two directly connected routers running OSPF to establish a neighbor adjacency?（）
Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 1tunnel source loopback 1tunnel destination 192.168.1.2tunnel mode ipv6ip isatapipv6 address 2000::/64 eui - 64
The following output occurs on Router R1 , which runs both EIGRP for IPv6 and OSPFv3, with redistribution from EIGRP into OSPF configured with the redistribute eigrp 1 metric 25 command. Interface S0/0/1 has been enabled for EIGRP ASN 1. Which of the following should be true of redistribution in this case?（）D 2000::/64 [90/1422516]via FE80::213:19FF:FE7B:5026, Serial0/0/1C 2000:0:0:1::/64 [0/0]via Serial0/0/1, directly connectedL 2000::1:213:19FF:FE7B:5004/128 [0/0]via Serial0/0/1, receive
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output？（）B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18