On a Cisco 1000 Series controller-based access point， the alarm LED is flashing red， but the other LEDsare off.
What is this access point indicating？（）
A.It has lost contact with the controller.
B.It requires a code upgrade.
C.It is operating normally.
D.Its IP address already exists.
您可能感興趣的試卷
你可能感興趣的試題
On a standalone access point， client association using EAP-Cisco Wireless （Cisco-LEAP） is failing， butassociation using EAP-PEAP is functioning.
What needs to be enabled on the standalone access point tocorrect this issue？（）
A.a shared key
B.network EAP
C.open authentication plus EAP
D.open authentication plus MAC
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2. H-REAP AP2 has six other clients associated to it， which continue to pass traffic.
What has caused this problem？（）
A.H-REAP AP1 lost its connection to the controller.
B.H-REAP AP2 lost its connection to the controller.
C.H-REAP AP1 has reached its client limit.
D.H-REAP AP2 has reached its client limit.
A Cisco Aironet 1020 controller-based access point has been connected to a Catalyst 3550-24 PWRSwitch. However， when it is powered up， the access point fails.
What has caused this problem？（）
A.access point has not been initialized with the primary controller
B.switch port is not enabled
C.switch does not support 802.3af
D.access point does not support 802.11h
E.incorrect switch power supply
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installation mode.When you set the link back to operational mode you loose association to the root bridge.
Which action willcorrect the problem？（）
A.Configure the proper channel.
B.Enable passwords on both bridges.
C.Configure the distance parameter value.
D.Configure the bridge to force infrastructure devices to associate only to the SSID parameter.
On a Cisco Aironet 1130AG Series standalone access point，the status LED is dark blue andblinking.
What does this indicate？（）
A.The access point is booting.
B.The internal radio has failed.
C.An access point buffer overflow is occurring.
D.A firmware upgrade is in progress.
最新試題
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS？ （）
What is the maximum number of wireless controllers that the highest-end Cisco WCS server canmanage？（）
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side，which of the following actionsshould you perform on the wired infrastructure？（）
You have a very few Cisco 7920 wireless IP phones on your network， but lots of wireless laptops.You want to increase the bandwidth available for the laptops by decreasing the bandwidth reserved for the Cisco 7920 phones.What is the lowest percentage of voice-allocated bandwidthyou can select on the WLAN controller？（）
On a Cisco Aironet 1240AG Series standalone access point， the radio LED is dark blue and blinking，but the status LED and Ethernet LED are both off.What does this indicate？（）
How many WLANs can a Cisco Aironet 1242 in H-REAP mode support when actively connected toa wireless controller？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but， when you answer， the call is dropped.What may cause this problem？（）
On a WLAN controller， what is the default roaming bandwidth percentage reserved for voice clients？（）
The IOS of a North American Cisco Aironet 1130AG Series standalone access point has becomecorrupt. You must therefore reload the TFTP firmware.Before you press and hold the MODEbutton， you should verify that the file name is which of the following？（）
You have been called upon to add location-based services into an existing controller-basedwireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference？（）