You are configuring an RF group of controllers that coordinate Radio Resource Management calculations.
What is the maximum number of WLAN controllers that you can add？（）
A.12
B.17
C.20
D.24
您可能感興趣的試卷
你可能感興趣的試題
A.QoS Element for Wireless Phones
B.IGMP Snooping
C.WMM
D.AVVID Priority Mapping
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor， 4 GBRAM， and an 80 GB hard drive. A location appliance has been incorporated into the network and is beingmonitored by the Cisco WCS. There are 3000 devices to be tracked but not all of them are being trackedon the Cisco WCS.
What can be done to correct the problem？（）
A.Add 4 GB of RAM to the Cisco WCS.
B.Add a 120 GB hard drive to the Cisco WCS.
C.Add a new location appliance.
D.Add a new Cisco WCS server dedicated to the location appliance.
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN. The phonerings but， when you answer， the call is dropped.
What may have caused this problem？（）
A.The minimum data rate is not set to 11 Mbps.
B.An address resolution protocol is enabled.
C.Publicly Secure Packet forwarding is enabled.
D.The access point is set to the least congested channel.
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standaloneWLAN.
What may have caused this problem？（）
A.The minimum data rate is not set to 11 Mbps.
B.An address resolution protocol has been disabled.
C.Publicly Secure Packet forwarding is enabled.
D.The access point is set to the least congested channel.
最新試題
You are trying to change the polling parameters used by the location manager via the Cisco WCS，and your request is being denied. What is wrong？（）
On a Cisco Aironet 1240AG Series standalone access point， the radio LED is dark blue and blinking，but the status LED and Ethernet LED are both off.What does this indicate？（）
You have been called upon to add location-based services into an existing controller-basedwireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference？（）
You have a very few Cisco 7920 wireless IP phones on your network， but lots of wireless laptops.You want to increase the bandwidth available for the laptops by decreasing the bandwidth reserved for the Cisco 7920 phones.What is the lowest percentage of voice-allocated bandwidthyou can select on the WLAN controller？（）
Static WEP is configured on the access point. You are authenticated and associated to the accesspoint but are unable to obtain an IP address.Which of the following will cause this problem？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but， when you answer， the call is dropped.What may cause this problem？（）
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor，4GB RAM， and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem？（）
The IOS of a North American Cisco Aironet 1130AG Series standalone access point has becomecorrupt. You must therefore reload the TFTP firmware.Before you press and hold the MODEbutton， you should verify that the file name is which of the following？（）
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side，which of the following actionsshould you perform on the wired infrastructure？（）
You are using ADU and are authenticated and associated to an access point. However， you are unable to obtain an IP address.Which of these has caused this problem？（）