A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2.H-REAP AP2 has six other clients associated to it, which continue to pass traffic.
What has causedthis problem?()
A.H-REAP AP1 lost its connection to the controller.
B.H-REAP AP2 lost its connection to the controller.
C.H-REAP AP1 has reached its client limit.
D.H-REAP AP2 has reached its client limit.
您可能感興趣的試卷
你可能感興趣的試題
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.
Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS? ()
A.064 Tunnel-Type
B.066 Tunnel-Client-Endpoint
C.067 Tunnel-Server-Endpoint
D.081 Tunnel-Private-Group-ID
E.082 Tunnel-Assignment-ID
F.083 Tunnel-Preference
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is, you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.
What level do you set the bandwidth to?()
A.5 percent
B.15 percent
C.25 percent
D.35 percent
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.
In addition to implementing PSPF or peer-to-peer blocking on the wireless side,which of the following actionsshould you perform on the wired infrastructure?()
A.Take no action, you have achieved your goal.
B.Implement a Cisco Secure IPS sensor.
C.Implement a protected port on the access switches.
D.Implement 802.1X on the switch ports.
A.Aggressive Load Balancing on
B.Aggressive Load Balancing off
C.Multicast on
D.Multicast off
E.AP Fallback on
F.AP Fallback off
A.MS-CHAP v2
B.PAP
C.GTC
D.MD5
最新試題
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but, when you answer, the call is dropped.What may cause this problem?()
Which of the following parameter sets must be configured on the Cisco Wireless Location Appliance?()
What is the maximum number of wireless controllers that the highest-end Cisco WCS server canmanage?()
The IOS of a North American Cisco Aironet 1130AG Series standalone access point has becomecorrupt. You must therefore reload the TFTP firmware.Before you press and hold the MODEbutton, you should verify that the file name is which of the following?()
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS? ()
You have been called upon to add location-based services into an existing controller-basedwireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference?()
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side,which of the following actionsshould you perform on the wired infrastructure?()
You are installing a Cisco 4402 Series Wireless LAN Controller.What type of interface is used on the uplink port?()
You have a very few Cisco 7920 wireless IP phones on your network, but lots of wireless laptops.You want to increase the bandwidth available for the laptops by decreasing the bandwidth reserved for the Cisco 7920 phones.What is the lowest percentage of voice-allocated bandwidthyou can select on the WLAN controller?()
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor,4GB RAM, and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem?()