The BGP routing table consists of the following network routes:
What is the correct command to summarize these prefixes into a single summary prefix of192.168.12.0/22 while also allowing for the advertisement of the more specific prefixes?()
A.network 192.168.12.0 mask 255.255.252.0
B.network 192.168.12.0 mask 0.0.3.255
C.network 192.168.12.0
D.aggregate-address 192.168.12.0 255.255.252.0
E.aggregate-address 192.168.12.0 255.255.252.0 summary-only
F.aggregate-address 192.168.12.0 255.255.252.0 as-set
您可能感興趣的試卷
你可能感興趣的試題
A.A peer router running IBGP
B.A peer router running EBGP
C.A community member running IBGP
D.A peer group member running IBGP
E.A peer group member running EBGP
A BGP router is configured as shown below:
interface ethernet 0
ip address 10.10.10.1 255.255.0.0!
int serial 0
ip address 172.16.1.1 255.255.255.252!
router bgp 65001
neighbor 192.168.1.1 remote-as 65002
Based on the above configuration, which of the following BGP statements would inject the10.10.0.0/16 prefix into the BGP routing table?()
A.network 10.0.0.0
B.network 10.10.0.0 mask 255.255.0.0
C.network 10.10.10.1 mask 255.255.255.255
D.network 10.10.10.0 mask 255.255.255.0
E.network 10.0.0.0 mask 255.255.0.0
A.The IBGP routers must always be fully meshed
B.The IBGP routers can be in a different AS
C.The IBGP routers must be directly connected
D.The IBGP routers do not need to be directly connected
E.None of the other alternatives apply are true
The network consists of two separate autonomous systems as shown below:
You need to configure Router R2 as a BGP route reflector and Router R1 as the client. Assumingthat Router R3 isn’t running BGP, which two of the commands below would you enter on R2 tosatisfy your goals?()
A.neighbor 165.50.12.1 remote-as 65100
B.neighbor 165.50.12.2 remote-as 64000
C.neighbor 165.50.12.1 route-reflector-client
D.neighbor 165.50.12.2 route reflector-client
Refer to the exhibit. All routers are configured for BGP. EBGP routes received on router R2 showup in the BGP table on routers R1 and R3 but not in their IP routing tables. What would causethis?()
A.EBGP multihop is not configured on routers R1 and R3
B.Routers R1 and R3 do not receive the same routes via an IGP
C.Synchronization in autonomous system 100 is turned is on
D.The BGP routers in autonomous system 100 are not logically fully-meshed
E.Synchronization in autonomous system 100 is turned is off
最新試題
You need to configure a GRE tunnel on a IPSec router. When you are using the SDM to configurea GRE tunnel over IPsec, which two parameters are required when defining the tunnel interfaceinformation?()
In computer security, AAA stands for authentication, authorization and accounting. Which optionabout the AAA authentication enable default group radius enable command is correct?()
IPSec VPN is a widely-acknowledged solution for enterprise network. What are the four steps tosetup an IPsec VPN?()
Network Topology Exhibit:Configuration Exhibit:NET(config)# access-list 112 deny icmp any any echo logNET(config)# access-list 112 deny imp any any redirect logNET(config)# access-list 112 deny icmp any any mask-request logNET(config)# access-list 112 permit icmp any 10.1.1.0 0.0.0.255NET(config)# interface Fa0/1NET(config-if)# ip access-group 112 inYou work as a network administrator at networkTut.com, study the exhibit carefully. Theconfiguration has been applied to router NET to mitigate the threat of certain types of ICMPbasedattacks while allowing some ICMP traffic to the corporate LAN to work. However, the configurationis incorrect. On the basis of the information in the exhibit, which configuration option wouldcorrectly configure router NET?()
Which two encapsulation methods require that an 827 ADSL router be configured with a PPPusername and CHAP password?()
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clickingthe numbers to the left of each question. In order to complete the questions, you will need to referto the SDM and the topology, neither of which is currently visible. To gain access to either thetopology or the SDK click on the button to left side of the screen that corresponds to the sectionyou wish to access. When you have finished viewing the topology the SDK you can return to yourquestions by clicking on the Questions button to the left.Which IPSec rule is used for the Olympia branch and what does it define?()
cisco ios command to interface dialer 0
Drag the protocols that are used to distribute MPLS labels from the above to the target area on thebelow.(Not all options will be used)
Match the xDSL type on the above to the most appropriate implementation on the below.
Authentication is the process of determining if a user or identity is who they claim to be. Refer tothe exhibit. Which statement about the authentication process is correct?()