A.Only OSPF version 3 can be utilized for routing IPv4 and IPv6
B.IPv4 and IPv6 networks can be routed simultaneously
C.IPv6 can be routed using the same routing protocol versions as IPv4
D.A router routing for IPv6 and IPv4 must convert IPv4 packets to IPv6 packets to route them
E.None of the other alternatives apply
您可能感興趣的試卷
你可能感興趣的試題
A.192.168.30.1：0：0：0：0：0：0
B.0：0：0：0：0：0：192.168.30.1
C.：：192.168.30.1
D.C0A8：1E01：：
E.192.168.30.1：：
F.：：C0A8：1E01
A.The route table is cleared. Then the OSPF neighbors are reformed
B.The OSPF adjacencies are cleared and initiated again
C.The OSPF database is repopulated and then the shortest path first （SPF） algorithm isperformed.
D.The shortest path first （SPF） algorithm is performed on the LSA database
E.None of the other alternatives apply
Refer to the exhibit. What two statements are true？（）
A.The IP address of the backup designated router （BDR） is FE80：：205：5FFF：FED3：5808
B.This is the designated router （DR） on the FastEthernet 0/0 link
C.Interface FastEthernet 0/0 was configured with the ipv6 ospf 1 area 1 command
D.OSPF version 2 has been enabled to support IPv6
E.The output was generated by the show ip interface command
Refer to the output. What IOS command produces this output？（）
A.show ip ospf
B.show ip ospf interface
C.show ipv6 ospf interface
D.show ipv6 ospf
Refer to the exhibit. Assume that Switch_A is active for the standby group and the standby devicehas only the default HSRP configuration. What conclusion is valid？（）
A.If port Fa1/1 on Switch_A goes down， the standby device will take over as active
B.If the current standby device were to have the higher priority value， it would take over the role ofactive for the HSRP group
C.If Switch_A had the highest prioritynumber， it would not take over as active router
D.If port Fa1/1 on Switch_A goes down， the new priority value for the switch would be 190
最新試題
IPSec VPN is a widely-acknowledged solution for enterprise network. Which three IPsec VPNstatements are true？（）
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clickingthe numbers to the left of each question. In order to complete the questions， you will need to referto the SDM and the topology， neither of which is currently visible. To gain access to either thetopology or the SDK click on the button to left side of the screen that corresponds to the sectionyou wish to access. When you have finished viewing the topology the SDK you can return to yourquestions by clicking on the Questions button to the left.Which IPSec rule is used for the Olympia branch and what does it define？（）
Drag the DSL technologies on the left to their maximum（down/up） data rate values on the below.
Drag and drop each management protocol on the above to the correct category on the below.
Identify the recommended steps for worm attack mitigation by dragging and dropping them into thetarget area in the correct order.
IPSec VPN is a widely-acknowledged solution for enterprise network. What are the four steps tosetup an IPsec VPN？（）
Match the xDSL type on the above to the most appropriate implementation on the below.
Network Topology Exhibit：Configuration Exhibit：NET（config）# access-list 112 deny icmp any any echo logNET（config）# access-list 112 deny imp any any redirect logNET（config）# access-list 112 deny icmp any any mask-request logNET（config）# access-list 112 permit icmp any 10.1.1.0 0.0.0.255NET（config）# interface Fa0/1NET（config-if）# ip access-group 112 inYou work as a network administrator at networkTut.com， study the exhibit carefully. Theconfiguration has been applied to router NET to mitigate the threat of certain types of ICMPbasedattacks while allowing some ICMP traffic to the corporate LAN to work. However， the configurationis incorrect. On the basis of the information in the exhibit， which configuration option wouldcorrectly configure router NET？（）
As a network technician， do you know what is a recommended practice for secure configurationmanagement？（）
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clicking the numbers to the left of each question. In order to complete the questions， you will need to referto the SDM and the topology， neither of which is currently visible.To gain access to either the topology or the SDK click on the button to left side of the screen thatcorresponds to the section you wish to access. When you have finished viewing the topology theSDK you can return to your questions by clicking on the Questions button to the left.Which defined peer IP address an local subnet belong to Crete？（）