A. MST00
B. MST01
C. the last MST instance configured
D. none
您可能感興趣的試卷
你可能感興趣的試題
A. Region name
B. Configuration revision number
C. VLAN instance map
D. IST STP BPDU hello timer
E. CST instance map
F. PVST+ instance map
Which of the following specification will allow you to： associate VLAN groups to STP instances so you can provide multiple forwarding paths for data traffic and enable load balancing？ （）
A. IEEE 802.1d （STP）
B. IEEE 802.1s （MST）
C. IEEE 802.1Q （CST）
D. IEEE 802.1w （RSTP）
Which of the following specifications is a companion to the IEEE 802.1w Rapid Spanning Tree Protocol （RSTP） algorithm， and warrants the use multiple spanning-trees？ （）
A. IEEE 802.1s （MST）
B. IEEE 802.1Q （CST）
C. Cisco PVST+
D. IEEE 802.1d （STP）
E. None of the other alternatives apply
pany uses MSTP within their switched LAN.
What is the main purpose of Multiple Instance Spanning Tree Protocol （MSTP）？（）
A. To enhance Spanning Tree troubleshooting on multilayer switches
B. To reduce the total number of spanning tree instances necessary for a particular topology
C. To provide faster convergence when topology changes occur in a switched network
D. To provide protection for STP when a link is unidirectional and BPDUs are being sent but not received
E. None of the other alternatives apply
The Company network utilizes the Multiple-instance Spanning Tree protocol in its switched LAN.
Which three statements about the MST protocol （IEEE 802.1S） are true？ （）
A. To verify the MST configuration， the show pending command can be used in MST configuration mode.
B. When RSTP and MSTP are configured； UplinkFast and BackboneFast must also be enabled.
C. All switches in the same MST region must have the same VLAN-to-instance mapping， but different configuration revision numbers.
D. All switches in an MST region， except distribution layer switches， should have their priority lowered from the default value 32768.
E. An MST region is a group of MST switches that appear as a single virtual bridge to adjacent CST and MST regions.
F. Enabling MST with the "spanning-tree modemst" global configuration command also enables RSTP.
最新試題
Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1. What will be the result？（）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
Refer to the exhibit. For what purpose is the command show ip cef used？（）
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ？ （）
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）
If G1/0/1 on DS1 is shutdown， what will be the current priority value of the Vlan105’s group on DS1 ？（）
Refer to the exhibit. Based on the output of the show spanning-tree command， which statement is true？ （）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
Refer to the exhibit. Which Virtual Router Redundancy Protocol （VRRP） statement is true about the roles of the master virtual router and the backup virtual router？（）