多項選擇題Which of the following are methods EIGRP uses to initially populate (seed) its EIGRP topology table, before learning topology data from neighbors?()

A.By adding all subnets listed by the show ip route connected command
B.By adding the subnets of working interfaces over which static neighbors have been defined
C.By adding subnets redistributed on the local router from another routing source
D.By adding all subnets listed by the show ip route static command


您可能感興趣的試卷

你可能感興趣的試題

2.多項選擇題Which of the following settings could prevent two potential EIGRP neighbors from becoming neighbors?()

A. The i nterface used by one router to connect to the other router is passive in the EIGRP process.
B. Duplicate EIGRP router IDs.
C. Mismatched Hold Timers.
D. IP addresses of 10.1.1.1/24 and 10.2.2.2/24, respectively.

5.單項選擇題

Routers R1 and R2 are EIGRP neighbors using their Fa0/0 interfaces, respectively. An engineer adds the ip hello - interval eigrp 9 6 command to R1's Fa0/0 configuration.
Which of the following is true regarding the results from this c hange?()

A.The show ip eigrp neighbors command on R1 lists the revised Hello timer
B.The show ip eigrp interfaces command on R1 lists the revised Hello timer
C.The R1 - R2 neighborship fails due to Hello timer mismatcH
D.The show ip eigrp interfaces detail command on R1 lists the revised Hello timer

最新試題

The following configura tion exists on a router on one end of an IPv6 tunnel. Which type of tunnel is created by this configuration?()interface loopback 1ip address 1.1.1.1 255.255.255.255interface tunnel 2ipv6 address 2000::1::/64tunnel source loopback 1tunnel destina tion 2.2.2.2tunnel mode ipv6ipipv6 eigrp 1

題型:單項選擇題

Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?()ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0

題型:單項選擇題

An Enterprise rou ter, Ent1, displays the following excerpt from the show ip bgp command. ENT1 has an eBGP connection to an ISP router with address 3.3.3.3 and an iBGP connection to a router with address 4.4.4.4. Which of the following is most likely to be true?()Network  Next Hop Metric LocPrf Weight Path*> 3.3.3.3 0 0 1 1 1 1 218 i

題型:單項選擇題

The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output?()B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18

題型:單項選擇題

Which of the following answers lists either a protocol or function that can be used by a host to dynamically learn its own IPv6 address?()

題型:多項選擇題

Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?()

題型:單項選擇題

Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network.Which of the following answers best describes the router's logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?()

題型:單項選擇題

A client host uses IPv4 to communicate with one ser ver and IPv6 to communicate with another.Which of the following IPv6 coexistence features is likely at work on the host?()

題型:單項選擇題

Look at the following configuration below and select the statements that are true.()RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0

題型:多項選擇題

Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?()interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 1tunnel source loopback 1tunnel destination 192.168.1.2tunnel mode ipv6ip isatapipv6 address 2000::/64 eui - 64

題型:單項選擇題