The following configura tion exists on a router on one end of an IPv6 tunnel. Which type of tunnel is created by this configuration?（）
interface loopback 1
ip address 1.1.1.1 255.255.255.255
interface tunnel 2
ipv6 address 2000::1::/64
tunnel source loopback 1
tunnel destina tion 2.2.2.2
tunnel mode ipv6ip
ipv6 eigrp 1
A. Automatic 6to4
B. Manually configured tunnel
C. ISATAP
D. GRE
您可能感興趣的試卷
你可能感興趣的試題
A. Native IPv6
B. Point - to -point tunnels
C. Multipoint tunnels
D. NAT - PT
E. Dual stacks
An enterprise has plans to start adding IPv6 support. The initial deployment requires support from some IPv6 - only device s that need to access servers that support only IPv4.
Which of the following tools would be most appropriate?（）
A. Native IPv6
B. Point - to -point tunnels
C. Multipoint tunnels
D. NAT - PT
An enterprise h as plans to start adding IPv6 support. For the first year, the IPv6 will be in small pockets spread around the existing large IPv4 network, with occasional IPv6 traffic while applications teams test IPv6 - enabled servers and applications.
Which of the fol lowing tools would be most appropriate?（）
A. Native IPv6
B. Point - to -point tunnels
C. Multipoint tunnels
D. NAT - PT
A. Metric
B. Administrative distance
C. Timeout (seconds)
D. Prefix length
E. Interface ID
The following output occurs on Router R1 , which runs both EIGRP for IPv6 and OSPFv3, with redistribution from EIGRP into OSPF configured with the redistribute eigrp 1 metric 25 command. Interface S0/0/1 has been enabled for EIGRP ASN 1. Which of the following should be true of redistribution in this case?（）
D 2000::/64 [90/1422516]
via FE80::213:19FF:FE7B:5026, Serial0/0/
1
C 2000:0:0:1::/64 [0/0]
via Serial0/0/1, directly connected
L 2000::1:213:19FF:FE7B:5004/128 [0/0]
via Serial0/0/1, receive
A. Route 2000::/64 will be redistributed.
B. Route 2 000:0:0:1::/64 will be redistributed.
C. Route 2000:1:213:19FF:FE7B:5004/128 will be redistributed.
D. No routes will be redistributed because of the omission of the subnets parameter of the redistribute command.
最新試題
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）
Which of the following must match for two directly connected routers running OSPF to establish a neighbor adjacency?（）
The following configura tion exists on a router on one end of an IPv6 tunnel. Which type of tunnel is created by this configuration?（）interface loopback 1ip address 1.1.1.1 255.255.255.255interface tunnel 2ipv6 address 2000::1::/64tunnel source loopback 1tunnel destina tion 2.2.2.2tunnel mode ipv6ipipv6 eigrp 1
Router R1 sits at an Enterprise branch office, using the Internet for its only connectivity back to the rest of the EnterprisE.Which of the following is not a ben efit of using an IPsec tunnel for packets sent through the Internet, between R1 and the rest of the Enterprise?（）
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?（）
Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?（）interface f0/0mac - address 1111.1111.1 111ipv6 address 2000::/64 eui - 64ipv6 address 2001::1/64
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output？（）B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18
Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?（）
The following output on Router R1 lists details of a BGP route for 190.1.0.0/16. Which of the following is true based on this output?（）R1# show ip bgp 19 0.1.0.0/16BGP routing table entry for 190.1.0.0/16, version 121Paths: (1 available, best #1, table Default - IP - Routing - Table)Advertised to update - groups:11 2 3 41.1.1.1 from 2.2.2.2 (3.3.3.3)Origin IGP, metric 0, localpref 100, valid, internal, best
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0