多項選擇題The Peanut router is able to successfully ping the Serial 0 and Ethernet 0 interface of the Popcorn router, but a ping issued to the Ethernet 1 interface fails. Based on the above output, what are the potential causes of this problem?()

A. The Popcorn router is not forwarding RIP updates.
B. The Popcorn router did not include network 192.168.12.0 in its routing configuration.
C. The Ethernet1 interface of the Popcorn router is shutdown.
D. The clockrate is not present in the configuration of one of the routers.
E. The Serial interface of the Popcorn router is not operating.


您可能感興趣的試卷

你可能感興趣的試題

1.單項選擇題Which one of the following EIGRP commands can check the IP addresses of the adjacent neighbors, as well as verifying the EIGRP retransmit intervals and queue counts?()

A. TK1#show ip eigrp adjacency
B. TK1#show ip eigrp topology
C. TK1#show ip eigrp interfaces
D. TK1#show ip eigrp neighbors
E. None of the above

2.單項選擇題

A new router, named TK1, is being installed. You wish to add this router to your existing OSPF network. In doing so, you configure the following:
TK1(config)# router ospf 1
TK1(config-router)# network 10.10.10.0 255.255.255.0 area 0
After making this change, you notice that the networks attached to TK1 are not being learned by the other OSPF routers. What could be the cause of this?()

A. The AS is not correctly configured
B. The network subnet mask is incorrectly configured
C. The network wildcard mask is configured incorrectly
D. The network number is not correctly configured
E. The process id is configured incorrectly
F. None of the above

3.單項選擇題

On your OSPF network, routers TK1 and TK2 belong to the same Ethernet network. However, they are unable to establish an adjacency over this link. While troubleshooting this problem, you issue the "show ip ospf interface Ethernet 0"command on each router. The output from these commands is displayed below:
What is the underlying cause of the routers failing to become adjacent?()

A. The OSPF area is misconfigured.
B. The priority on TK2 should be set lower.
C. The cost on TK2 should be set lower.
D. The hello and dead timers are misconfigured.
E. You need to add a backup designated router to the network.
F. The OSPF process ID numbers do not match.


5.單項選擇題Which one of the following privileged EXEC mode IOS show commands will display the state of the OSPF DR/BDR (designated router / backup designated router) election process?()

A. TK1# show ip ospf interface
B. TK1# show ip ospf priority
C. TK1# show ospf neighbor detail
D. TK1# show ospf processes
E. TK1# show ospf neighbor state

最新試題

Which of the following correctly describe steps in the OSI data encapsulation process?()

題型:多項選擇題

A network host is configured as follows: Host IP address: 192.168.16.183 Subnet mask: 255.255.255.224 Default gateway: 192.168.16.190 Which of the following statements describe the network to which this host is attached?()

題型:多項選擇題

A Router with a BRI/T interface will be used for an ISDN Connection what other ISDN device is required to complete this connection? ()

題型:單項選擇題

What is the purpose of typing o/r 0x2142 during a password recover procedure on a 2500 series router?()

題型:單項選擇題

What should the configuration register value be after successfully completing the password recover procedure and returning the router to normal operation? ()

題型:單項選擇題

Which of the following contribute to congestion on an Ethernet network?()

題型:多項選擇題

All WAN links is side the TestKing.com network use PPP with for authentication security. Which command will display the CHAP authentication process as it occurs between two routers in the network?()

題型:單項選擇題

What is the subnetwork address for a host with IP address 201.100.5.68/28?()

題型:單項選擇題

Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? ()

題型:單項選擇題

Which command is used to display the placement and direction of an IP access control list on a router?()

題型:單項選擇題