You want to implement router redundancy in the Company network using the best method available.
Which protocol specified by RFC 2281 provides network redundancy for IP networks， ensuring that user traffic immediately and transparently recovers from first-hop failures in network edge devices or access circuits？（）
A. ICMP
B. IRDP
C. HSRP
D. STP
E. None of the other alternatives apply
您可能感興趣的試卷
你可能感興趣的試題
pany uses GLBP to provide for router redundancy in the network.
Which describes the default load balancing scheme used by the Gateway Load Balancing Protocol （GLBP）？（）
A. Per host basis using a strict priority scheme
B. Per session using a round-robin scheme
C. Per session using a strict priority scheme
D. Per GLBP group using a strict priority scheme
E. Per host basis using a round-robin scheme
F. Per GLBP group using a round-robin scheme
HSRP has been configured between two Company devices.
Which of the following describe reasons for deploying HSRP？ （）
A. HSRP provides redundancy and fault tolerance
B. HSRP allows one router to automatically assume the function of the second router if the second router fails
C. HSRP allows one router to automatically assume the function of the second router if the second router starts
D. HSRP provides redundancy and load balancing
You want to implement a high availability network using two Cisco routers. You also want to ensure that the stat of the WAN interfaces can be tracked in doing so.
Which router redundancy protocol cannot be configured for interface tracking？ （）
A. GLBP
B. HSRP
C. RPR
D. VRRP
E. SLB
F. RPR+
G. None of the other alternatives apply
You need to configure two Company routers for high availability.
Which protocol enables a group of routers to form a single virtual router and use the real IP address of a router as the gateway address？ （）
A. HSRP
B. IRDP
C. Proxy ARP
D. GLBP
E. VRRP
F. None of the other alternatives apply
You have just purchased a new Cisco 3560 switch running the enhanced IOS and need configure it to be installed in a high availability network. On a 3560 EMI switch，
which three types of interfaces can be used to configure HSRP？（）
A. SVI interface
B. Access port
C. EtherChannel port channel
D. Loopback interface
E. Routed port
F. BVI interface
最新試題
Refer to the exhibit. Which statement is true about the output？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Which router redundancy protocol cannot be configured for interface tracking？（）
Which three statements are true of the Link Aggregation Control Protocol （LACP）？（）
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this？（）
What is the configured priority value of the Vlan105’s group on DS2 ？（）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
Which two statements are true when the extended system ID feature is enabled？ （）
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）