Refer to the exhibit.
Which two problems are the most likely cause of the exhibited output？（）
A. transport layer issues
B. VRRP misconfiguration
C. HSRP misconfiguration
D. physical layer issues
E. spanning tree issues
您可能感興趣的試卷
你可能感興趣的試題
Examine the router output above. Which two items are correct？（）
A. The local IP address of Router A is 10.1.0.6.
B. The local IP address of Router A is 10.1.0.20.
C. If Ethernet 0/2 goesdown， the standby router will take over.
D. When Ethernet 0/3 of RouterA comes back up， the priority will become 105.
E. Router A will assume the active state if its priority is the highest.
What can be determined about the HSRP relationship from the displayed debug output？ （）
A. Router 172.16.11.112 will be the active router because its HSRP priority is preferred over router 172.16.11.111.
B. Router 172.16.11.111 will be the active router because its HSRP priority is preferred over router 172.16.11.112.
C. The IP address 172.16.11.111 is the virtual HSRP router IP address.
D. The IP address 172.16.11.112 is the virtual HSRP router IP address.
E. The nonpreempt feature is enabled on the 172.16.11.112 router.
F. The preempt feature is not enabled on the 172.16.11.111 router.
Refer to the exhibit. Based upon the debug output that is shown，
which three statements about HSRP are true？（）
A. The router with IP address 172.16.11.111 haspreempt configured.
B. The final active router is the router with IP address 172.16.11.111.
C. The router with IP address 172.16.11.112 has nonpreempt configured.
D. The priority of the router with IP address 172.16.11.112 is preferred over the router with IP address 172.16.11.111.
E. The router with IP address 172.16.11.112 is using default HSRP priority.
F. The IP address 172.16.11.115 is the virtual HSRP IP address.
A. independent of SSO
B. NSF combined with SSO enables supervisor engine load balancing
C. supported by RIPv2， OSPF， IS-IS， and EIGRP
D. supports IPv4 and IPv6 multicast
E. prevents route flapping
F. dependent on FIB tables
pany has a Catalyst 6500 and you need to configure redundancy between the supervisor modules. With route processor redundancy （RPR+）， the redundant supervisor engine is fully initialized and configured， which shortens the switchover time if the active supervisor engine fails.
Which three statements are true about the RPR + operations when the redundant supervisor engine switched over the failed primary supervisor engine？ （）
A. Static IP routes are maintained across a switchover because they are configured from entries in the configuration file.
B. Information about dynamic routing states， maintained on the active supervisor engine， is synchronized to the redundant supervisor engine and is transferred during the switchover.
C. Information about dynamic routing states， maintained on the active supervisor engine， is not synchronized to the redundant supervisor engine and is lost on switchover.
D. The Forwarding Information Base （FIB） tables are cleared on a switchover. As a result， routed traffic is interrupted until route tables reconverge.
E. Static IP routes are cleared across a switchover and recreated from entries in the configuration file on the redundant supervisor engine.
F. The Forwarding Information Base （FIB） tables are maintained during the switchover. As a result， routed traffic continues without any interruption when the failover occurs.
最新試題
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Refer to the exhibit. What will happen when one more user is connected to interface FastEthernet 5/1？ （）
Refer to the exhibit. For what purpose is the command show ip cef used？（）
Refer to the exhibit. Based on the output of the show spanning-tree command， which statement is true？ （）
Which three statements are true of the Link Aggregation Control Protocol （LACP）？（）
Refer to the exhibit. Which Virtual Router Redundancy Protocol （VRRP） statement is true about the roles of the master virtual router and the backup virtual router？（）
During routine maintenance， it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time， DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ？ （）
Which statement is correct about the use of the virtual interface on a WLC ？（）
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statements about the STP process for VLAN 200 are true？ （）
Which router redundancy protocol cannot be configured for interface tracking？（）