Refer to the exhibit. You want to use all the routes in the EIGRP topology for IP load balancing. Which two EIGRP subcommands wou ld you use to accomplish this goal?()
A. traffic - share balanced
B. distance
C. maximum- paths
D. default - network
E. variance
您可能感興趣的試卷
你可能感興趣的試題
A. performing inter - VLAN routing
B. performing 802.1Q trunking
C. performi ng ISL trunking
D. Ethernet Switch Module installed
E. ADSL WIC installed
F. running Call Manager Express
A. PPPoE
B. DOCSIS
C. CMTS
D. AAL5
A. to provide VPN access over L2TP
B. to enable PPP session from the router to the termination device at the headend for metro Ethernet connectivity
C. for DSL connectivity and removing the need for the end - user PC to ru n the PPPoE client software
D. for connecting the router to a cable modem, which bridges the Ethernet frames from the router to the cable modem termination system
A. PPPoA
B. PPPoE
C. PPP
D. L2TP
E. ATM
You have implemented mutual route redistribution between OSPF and EIGRP on a border router. When checking the routing table on one o f the OSPF routers within the OSPF routing domain, you are seeing some, but not all of the expected routes.
Which two things should you verify to troubleshoot this problem?()
A. The border router is using a proper seed metric for OSPF
B. The border ro uter is using a proper seed metric for EIGRP
C. The administrative distance is set for OSPF and EIGRP
D. The missing EIGRP routes are present in the routing table of the border router
E. The subnet keyword on the border router in the redistribute EIG RP command
最新試題
Which of the following is helpful to allow an IPv6 host to learn the IP address of a default gateway on its subnet?()
Which of the following answers lists either a protocol or function that can be used by a host to dynamically learn its own IPv6 address?()
Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?()interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 1tunnel source loopback 1tunnel destination 192.168.1.2tunnel mode ipv6ip isatapipv6 address 2000::/64 eui - 64
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?()
An enterprise has plans to start adding IPv6 support. The initial deployment requires support from some IPv6 - only device s that need to access servers that support only IPv4.Which of the following tools would be most appropriate?()
The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer?()interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1
An enterprise h as plans to start adding IPv6 support. For the first year, the IPv6 will be in small pockets spread around the existing large IPv4 network, with occasional IPv6 traffic while applications teams test IPv6 - enabled servers and applications.Which of the fol lowing tools would be most appropriate?()
Which of the following answers lists a multicast IPv6 address?()
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?()
Which of the following must match for two directly connected routers running OSPF to establish a neighbor adjacency?()