OSPF is enabled on router A. You execute the following command on router A and receive theaccompanying output:RouterA#ping 224.0.0.5 repeat1Type escape sequence to abort.Sending 1, 1 00 - byte ICMP Echos to 224.0.0.5, timeout is 2 seconds:Reply to request 0 from 10.100.100.1, 4 ms10.100.100.1 is the IP address of a loopback interface on router A.
What can you conclude about router A?（）
A. Only the router A loopback interface is parti cipating in the OSPF routing process
B. None of the router A interfaces are participating in the OSPF routing process
C. Router A is using the loopback interface IP address as its OSPF router ID
D. Router A does not have any reachable OSPF neighbors
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibits. You are verifying your OSPF implementation, and it does not seem to be functioning properly. What can you conclude from the exhibit and the show running - configuration command output? （）
A. The OSPF areas are not configured correctly.
B. The wildcard masks for the 10.x .x.x networks are incorrect.
C. The 172.16.x.x networks need to be connected to area 0 using virtual links.
D. The 172.16.x.x networks are discontiguous. OSPF is automatically summarizing them to 172.16.0.0/16 and data is being "black holed."
E. There is not enough information to make a determination.
Refer to the exhibits. Router B should advertise the network co nnected to the E0/0/0 interface to router A and block all other network advertisements. The IP routing table on router A indicates that it is not receiving this prefix from router B. What is the probable cause of the problem?（）
A. An access list on router B is causing the 192.168.3.16/28 network to be denied
B. An access list on router B is causing the 192.168.3.32/28 network to be denied
C. The distribute list on router B is referencing a numbered access list that does not exist on router B
D. The d istribute list on router B is referencing the wrong interface
After implementing EIGRP on your network, you issue the show ip eigrp traffic command on router C. The following output is shown:
What information can you determine about this network?（）
A. The network is stable
B. There is a flapping link or interface, and router C knows an alternate path to the network
C. There is a flapping link or interf ace, and router C does not know an alternate path to the network
D. EIGRP is not working correctly on router C
E. There is not enough information to make a determination
After implementing EIGRP on your network, you issue the show ip eigrp traffic command on router C. The following output is shown:
What can you conclude about this network? （）
A. The network has been stable for at least the last 45 minutes
B. There is a flapping link or interf ace, and router C knows an alternate path to the network
C. There is a flapping link or interface, and router A does not know an alternate path to the network
D. EIGRP is not working correctly on router C
E. There is not enough information to make a determination
Refer to the exhibit. Which statement about dynamic routing protocols for this network is true? （）
A.No dynamic interior routing protocol can summarize as shown
B.Unless configured otherwise, EIGRP would automatically summa rize the prefixes as shown in the exhibit
C.With this IP addressing scheme, EIGRP can be manually configured to summarize prefixes at the specified summarization points
D.The IP address design lends itself to OSPF Each summarizing router would be an ABR, summarizing to the next area in the address hierarchy
最新試題
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output？（）B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18
A client host uses IPv4 to communicate with one ser ver and IPv6 to communicate with another.Which of the following IPv6 coexistence features is likely at work on the host?（）
Which of the following answers lists either a protocol or function that can be used by a host to dynamically learn its own IPv6 address?（）
An enterprise has plans to start adding IPv6 support. The initial deployment requires support from some IPv6 - only device s that need to access servers that support only IPv4.Which of the following tools would be most appropriate?（）
The answers each list a tunnel method and two consecutive IPv6 address quartets.Which answers identify a tunneling method that relies on an IPv4 address to be embedded into an IPv6 address, within the correct quartets listed?（）
The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer？（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1
Which of the following must match for two directly connected routers running OSPF to establish a neighbor adjacency?（）
Router R1 lists the following output from a show command. Which of the following is true about R1?（）R1# show ip v6 interface f0/0FastEthernet0/0 is up, line protocol is upIPv6 is enabled, link - local address is FE80::213:19FF:FE12:3456No Virtual link - local address(es):Global unicast address(es):2000::4:213:19FF:FE12:3456, subnet is 2000:0:0:4::/64 [EUI]Jo ined group address(es):FF02::1FF02::2FF02::1:FF:12:3456
The following output occurs on Router R1 , which runs both EIGRP for IPv6 and OSPFv3, with redistribution from EIGRP into OSPF configured with the redistribute eigrp 1 metric 25 command. Interface S0/0/1 has been enabled for EIGRP ASN 1. Which of the following should be true of redistribution in this case?（）D 2000::/64 [90/1422516]via FE80::213:19FF:FE7B:5026, Serial0/0/1C 2000:0:0:1::/64 [0/0]via Serial0/0/1, directly connectedL 2000::1:213:19FF:FE7B:5004/128 [0/0]via Serial0/0/1, receive
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0