A.root
B.designated
C.alternate
D.backup
E.forwarding
F.learning
您可能感興趣的試卷
你可能感興趣的試題
A.dynamic desirable （VTP domain A） to dynamic desirable （VTP domain A）
B.dynamic desirable （VTP domain A） to dynamic desirable （VTP domain B）
C.dynamic auto （VTP domain A） to dynamic auto （VTP domain A）
D.dynamic auto （VTP domain A） to dynamic auto （VTP domain B）
E.dynamic auto （VTP domain A） to nonegotiate （VTP domain A）
F.nonegotiate （VTP domain A） to nonegotiate （VTP domain B）
A.Transparent mode always has a configuration revision number of 0.
B.Transparent mode cannot modify a VLAN database.
C.Client mode cannot forward received VTP advertisements.
D.Client mode synchronizes its VLAN database from VTP advertisements.
E.Server mode can synchronize across VTP domains.
A.Layer 2 switching and Layer 3 routing are mutually supported.
B.The port will not be associated with any VLAN.
C.The routed switch port supports VLAN subinterfaces.
D.The routed switch port is used when a switch has only one port per VLAN or subnet.
E.The routed switch port ensures that STP remains in the forwarding state.
Which two of the following steps are necessary to configure inter-VLAN routing between multilayer switches？（）
A.Configure a dynamic routing protocol.
B.Configure SVI interfaces with IP addresses and subnet masks.
C.Configure switch ports with network addresses.
D.Configure switch ports with the autostate exclude command.
E.Document the MAC addresses of the switch ports.
A switch that is to be added to the production network has been preconfigured （trunks， VLANs， VTP， and STP） and was tested in your lab. After installing the switch into the network， the entire network went down.
What might explain what happened？ （）
A.The new switch happened to be running Cisco Catalyst operating system， while the other network switches were running Cisco IOS Software.
B.The configuration revision of the new switch was higher than the configuration revision of the production VTP domain.
C.The link costs on the new switch are set to a high value， causing all ports on the new switch to go into a forwarding mode and none into blocking mode， thereby causing a spanning-tree loop.
D.The ports connecting to the two switches have been configured incorrectly. One side has the command switchport mode access and the other switchport mode trunk.
最新試題
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link？（）
Which two statements are true about BPDU port-guard and BPDU filtering？（）
Refer to the exhibit. On the basis of the output of the show spanning-tree inconsistentports command， which statement about interfaces FastEthernet 0/1 and FastEthernet 0/2 is true？（）
Which statement is correct about the use of the virtual interface on a WLC ？（）
How are STP timers and state transitions affected when a topology change occurs in an STP environment？（）
During routine maintenance， it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time， DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ？ （）
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
What is the configured priority value of the Vlan105’s group on DS2 ？（）
Refer to the exhibit. What does the command channel-group 1 mode desirable do？ （）