A. Only the path that is the feasible successor should be used.
B. Load balancing is disabled on t his router.
C. The router only performs equal - cost load balancing on all paths that have a metric greater than 1
D. The router performs equal - cost load balancing.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. On the basis of the partial configuration, which two statements are correct? （）
A. Only routes 10.0.1.0/24 will be sent out all interfaces.
B. Only routes matching 10.0.0.0/8 will be advertised out interfaces other than Ethernet 0.
C. Only routes matching 10.0.0.0/8 will be advertised out Ethernet 0.
D. Only routes matching 10.0.1.0/24 will be advertised out Ethernet 0.
E. Only routes 10.0.1.0/24 will be allowed in the routing table.
F. All rout es will be advertised out interfaces other than Ethernet 0.
A. many - to - one
B. one - to - one
C. one - to - many
D. many - to - many
A. After the router ospf 10 and passive - interface s0/0 commands have been issued , the s0/0 interface will not send any OSPF updates, but will receive routing updates on that interface
B. When you use the passive - interface command with RIPv2, multicasts are sent out the specified interface
C. After the router rip and passive -interface s0/0 commands have been issued, the s0/0 interface will not send any RIP updates, but will receive routing updates on that interface
D. When you use the passive - interface command with EIGRP, hel lo messages are not sent out the specified interface
E. After the router eigrp 10 and passive - interface s0/0 commands have been issued, the s0/0 interface will not send any EIGRP updates, but will receive routing updates on that interface
F. When you use the passive - interface command with OSPF, hello messages are not sent out the specified interface
Refer to the exhibit. What must be done on router RTA to ensure that EIGRP works effectively in a Frame Relay multipoint environment?（）
A. Issue the command bandwidth 224 on the physical interface.
B. Issue the command bandwidth 56 on the physical interface.
C. Issue the command bandwidth 224 on each subinterface.
D. Issue the command bandwidth 56 on each subinterface.
Which statement is correct based upon the following output from the show command on RT1 ? （）
A. OSPFv3 establishes neighbor adjacencies by using global IPv6 addresses.
B. OSPFv3 establishes neighbor adjacencies by using Link - local addresses.
C. RT1 owns a subnet mask of 64 bits.
D. OSPFv3 establishes neighbor adjacencies by using IPv4 addr esses.
最新試題
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network.Which of the following answers best describes the router's logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?（）
An Enterprise rou ter, Ent1, displays the following excerpt from the show ip bgp command. ENT1 has an eBGP connection to an ISP router with address 3.3.3.3 and an iBGP connection to a router with address 4.4.4.4. Which of the following is most likely to be true?（）Network Next Hop Metric LocPrf Weight Path*> 3.3.3.3 0 0 1 1 1 1 218 i
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）
Which of the following answers lists a multicast IPv6 address?（）
An enterprise has plans to start adding IPv6 support. The initial deployment requires support from some IPv6 - only device s that need to access servers that support only IPv4.Which of the following tools would be most appropriate?（）
Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 1tunnel source loopback 1tunnel destination 192.168.1.2tunnel mode ipv6ip isatapipv6 address 2000::/64 eui - 64
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（）interface f0/0ipv6 address 2345:0:0:8::1/64
The answers each list a tunnel method and two consecutive IPv6 address quartets.Which answers identify a tunneling method that relies on an IPv4 address to be embedded into an IPv6 address, within the correct quartets listed?（）
Look at the following configuration below and select the statements that are true.（）RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?（）