A. A neighbor distribute - list out command, referencing a standard ACL
B. A neighbor prefix - list out command
C. A neighbor filter - list out command
D. A neighbor distribute - list out command, referencing an extended ACL
E. A neighbor route - map out command
您可能感興趣的試卷
你可能感興趣的試題
R1 is currently advertising prefixes 1.0.0.0/8, 2.0.0.0/8, and 3.0.0.0/8 over its eBGP connection to neighbor 2.2.2.2 (R2). An engineer configures a prefix list (fred) on R1 that permits only 2.0.0.0/8 and then enables the filter with the neighbor R2 prefix- list fred out command. Upon exiting configuration mode, the engineer uses some show commands on R1, but no other commands.
Which of the following is true in this case?（）
A. The show ip bgp neighbor 2 .2.2.2 received -routes command lists the three original prefixes.
B. The show ip bgp neighbor 2.2.2.2 advertised - routes command lists the three original prefixes.
C. The show ip bgp neighbor 2.2.2.2 routes command lists the three original prefixes.
D. T he show ip bgp neighbor 2.2.2.2 routes command lists only 2.0.0.0/8.
E. The show ip bgp neighbor 2.2.2.2 advertised - routes command lists only 2.0.0.0/8.
A company uses Routers R1 and R2 to connect to ISP1 and ISP2, respectively, with Routers I1 and I2 used at th e ISPs. R1 peers with I1 and R2; R2 peers with I2 and R1. R1 and R2 do not share a common subnet, relying on other routers internal to the Enterprise for IP connectivity between the two routers.
Which of the following could be used to prevent potential routing loops in this design?（）
A. Using an iBGP mesh inside the Enterprise core
B. Configuring default routes in the Enterprise pointing to both R1 and R2
C. Redistributing BGP routes into the Enterprise IGP
D. Tunneling the packets for the i BGP connection between R1 and R2
A company uses Routers R1 and R2 to connect to ISP1 and ISP2, respectively, with Routers I1 and I2 used at the ISPs. R1 peers with I1 and R2; R2 peers with I2 and R1.
Assuming as many default s ettings as possible are used on all four routers, which of the following is true about the next - hop IP address for routes R1 learns over its iBGP connection to R2?（）
A. The next hop is I2's BGP RID
B. The next hop is I2's IP address used on the R2 - I2 neigh bor relationship
C. The next hop is R2's BGP RID
D. The next hop is R2's IP address used on the R1 - R2 neighbor relationship
The following output on Router R1 lists details of a BGP route for 190.1.0.0/16. Which of the following is true based on this output?（）
R1# show ip bgp 190.1.0.0/16
BGP routing table entry for 190.1.0.0/16, version 121
Paths: (1 available, best #1, table Default - IP - Routing - Table)
Advertised to update - groups:
1
1 2 3 4
1.1.1.1 from 2.2.2.2 (3.3.3.3)
Origin IGP, metric 0, localpref 100, valid, internal, best
A. R1 has a neighbor 1.1.1.1 command configured.
B. R1 has a neighbor 2.2.2.2 command configured.
C. The show ip bgp command lists a line for 190.1.0.0/16 with both a n > and an i on the left.
D. R1 is in ASN 1.
最新試題
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, and into the core of an Enterprise network. The branch also allows local hosts to communicate directly with public sites in th e Internet over this same DSL connection.Which of the following answers defines how the branch NAT config avoids performing NAT for the Enterprise directed traffic but does perform NAT for the Internet - directed traffic?（）
Router R1 sits at an Enterprise branch office, using the Internet for its only connectivity back to the rest of the EnterprisE.Which of the following is not a ben efit of using an IPsec tunnel for packets sent through the Internet, between R1 and the rest of the Enterprise?（）
Which of the following are true of both OSPFv2 and OSPFv3?（）
Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?（）interface f0/0mac - address 1111.1111.1 111ipv6 address 2000::/64 eui - 64ipv6 address 2001::1/64
An ISP has assigned prefix 3000:1234:5678::/48 to Company1. Which of the following terms would typically be used to describe this type of public IPv6 prefix?（）
The following output on Router R1 lists details of a BGP route for 190.1.0.0/16. Which of the following is true based on this output?（）R1# show ip bgp 19 0.1.0.0/16BGP routing table entry for 190.1.0.0/16, version 121Paths: (1 available, best #1, table Default - IP - Routing - Table)Advertised to update - groups:11 2 3 41.1.1.1 from 2.2.2.2 (3.3.3.3)Origin IGP, metric 0, localpref 100, valid, internal, best
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（）ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable
The following configura tion exists on a router on one end of an IPv6 tunnel. Which type of tunnel is created by this configuration?（）interface loopback 1ip address 1.1.1.1 255.255.255.255interface tunnel 2ipv6 address 2000::1::/64tunnel source loopback 1tunnel destina tion 2.2.2.2tunnel mode ipv6ipipv6 eigrp 1
Look at the following configuration below and select the statements that are true.（）RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0