A.ciscoaironet 1400 series
B.ciscoaironet 1300 series
C.ciscoaironet 1100 series
D.ciscoaironet 1240ag series
您可能感興趣的試卷
你可能感興趣的試題
On a cisco aironet 1130ag series standalone access point,the status led is dark blue and blinking.
What does this indicate？（）
A.the internal radio has failed.
B.a firmware upgrade is in progress.
C.an access point buffer overflow is occurring.
D.the access point is booting.
In a deployment using standalone access points， clients set up to authenticate with eap-peap or eap-cisco wireless （cisco-leap） cannot authenticatE. when you inspect the failed attempts report on the cisco secure acs， you find this error： "unknown network access server nas."
Which problem may have caused this failure？（）
A.misconfigured ip address of the aaa server on the access point
B.misconfigured eap type on the access point
C.misconfigured ip address of the access point on the aaa server
D.misconfigured eap type on the aaa server
A.router （config-ssid）# guest-mode
B.router （config-ssid）# advertise
C.router （config-ssid）# enable
D.router （config-ssid）# broadcast
Yours truly，customer has deployed a cisco wireless location appliance within its warehouse
environment. however， employees there have been experiencing problems when tracking objects using active rfid tags. the rfid tag data is not being collected.
On which device would you verify that rfids have been enabled？（）
A.access point
B.location manager
C.wireless controller
D.cisco wcs
A.partners having a discussion with customers about the minimum service components needed to successfully deploy a wireless solution
B.customers determining a competitor’s strategy for adopting advanced technologies
C.partners choosing the right products for their customers
D.customers choosing the right products for their network
E.customers defining the correct strategy for advanced technology adoption
最新試題
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2.H-REAP AP2 has six other clients associated to it， which continue to pass traffic.What has causedthis problem？（）
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor，4GB RAM， and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem？（）
You are using ADU and are authenticated and associated to an access point. However， you are unable to obtain an IP address.Which of these has caused this problem？（）
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side，which of the following actionsshould you perform on the wired infrastructure？（）
Which of the following accurately represents the functionality of a lightweight access point configured to operate in sniffer AP mode？（）
You have been called upon to add location-based services into an existing controller-basedwireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference？（）
On a WLAN controller， what is the default roaming bandwidth percentage reserved for voice clients？（）
You review the Failed Attempts logs on an AAA server and find： "unknown network access servererror." Which failure could produce this error？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but， when you answer， the call is dropped.What may cause this problem？（）
You are trying to change the polling parameters used by the location manager via the Cisco WCS，and your request is being denied. What is wrong？（）