You are charged with implementing a secure wireless installation which will provide Internet
access to client devices but will not allow communications between wireless clients. In addition toimplementing PSPF or peer-to-peer blocking on the wireless side.
Which of the following actionsshould you perform on the wired infrastructure？（）
A.Implement a Cisco Secure IPS sensor.
B.Implement 802.1X on the switch ports.
C.Take no action， you have achieved your goal.
D.Implement a protected port on the access switches.
您可能感興趣的試卷
你可能感興趣的試題
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.
Which two IETF RADIUS attributes should you configure on the Cisco SecureACS？（）
A.083 Tunnel-Preference
B.066 Tunnel-Client-Endpoint
C.064 Tunnel-Type
D.082 Tunnel-Assignment-ID
E.081 Tunnel-Private-Group-ID
F.067 Tunnel-Server-Endpoint
On a Cisco Aironet 1240AG Series standalone access point， the radio LED is dark blue andblinking，but the status LED and Ethernet LED are both off.
What does this indicate（）？
A.A firmware upgrade is in progress.
B.An access point buffer overflow is occurring.
C.The access point is booting.
D.The internal radio has failed.
A.router（config-ssid）# enable
B.router（config-ssid）# advertise
C.router（config-ssid）# broadcast
D.router（config-ssid）# guest-mode
A.cisco aironet 1500 series
B.cisco aironet 1400 series
C.cisco aironet 1300 series
D.cisco aironet 1200 series
You review the failed attempts logs on an aaa server and find： "unknown network access server error."
Which failure could produce this error？（）
A.failure of the wireless client and aaa server handshake
B.supplicant authentication failure
C.aaa client and aaa server handshake
D.wrong password used by the supplicant
最新試題
On a Cisco Aironet 1240AG Series standalone access point， the radio LED is dark blue and blinking，but the status LED and Ethernet LED are both off.What does this indicate？（）
The Cisco Wireless Location Appliance provides an audit trail for each device tracked for up to how many days？（）
On a Cisco Aironet 802.11 a/b/g wireless LAN client adapter，the status LED and activity LED are alternating on and off.What does this indicate？（）
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode. When you set the link back to operational mode you loose association to the root bridge.Which action will correct the problem？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is， you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.What level do you set the bandwidth to？（）
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standalone WLAN.What may cause this problem？（）
You are using ADU and are authenticated and associated to an access point. However， you are unable to obtain an IP address.Which of these has caused this problem？（）
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2.H-REAP AP2 has six other clients associated to it， which continue to pass traffic.What has causedthis problem？（）
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective？（）
You have a very few Cisco 7920 wireless IP phones on your network， but lots of wireless laptops.You want to increase the bandwidth available for the laptops by decreasing the bandwidth reserved for the Cisco 7920 phones.What is the lowest percentage of voice-allocated bandwidthyou can select on the WLAN controller？（）