A.Problem Management
B.Configuration Management
C.Incident Management
D.Change Management
您可能感興趣的試卷
你可能感興趣的試題
A.15
B.10
C.1
D.5
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A clientthat is anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.
Which message would best describe the establishment of the tunnel from the foreign controller’sperspective？（）
A.Received Mobile Anchor Export message
B.Transmit Plumbing duplex mobility tunnel message
C.Received Plumbing duplex mobility tunnel message
D.Transmit Mobile Anchor Export message
You are charged with implementing a secure wireless installation which will provide Internet
access to client devices but will not allow communications between wireless clients. In addition toimplementing PSPF or peer-to-peer blocking on the wireless side.
Which of the following actionsshould you perform on the wired infrastructure？（）
A.Implement a Cisco Secure IPS sensor.
B.Implement 802.1X on the switch ports.
C.Take no action， you have achieved your goal.
D.Implement a protected port on the access switches.
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.
Which two IETF RADIUS attributes should you configure on the Cisco SecureACS？（）
A.083 Tunnel-Preference
B.066 Tunnel-Client-Endpoint
C.064 Tunnel-Type
D.082 Tunnel-Assignment-ID
E.081 Tunnel-Private-Group-ID
F.067 Tunnel-Server-Endpoint
On a Cisco Aironet 1240AG Series standalone access point， the radio LED is dark blue andblinking，but the status LED and Ethernet LED are both off.
What does this indicate（）？
A.A firmware upgrade is in progress.
B.An access point buffer overflow is occurring.
C.The access point is booting.
D.The internal radio has failed.
最新試題
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but， when you answer， the call is dropped.What may cause this problem？（）
You are installing a Cisco 4402 Series Wireless LAN Controller.What type of interface is used on the uplink port？（）
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it， allthe LEDs on the access point blink together.What does this indicate about the access point？（）
You are configuring an RF group of controllers that coordinate Radio Resource Management calculations.What is the maximum number of WLAN controllers that you can add？（）
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor，4GB RAM， and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem？（）
You have a very few Cisco 7920 wireless IP phones on your network， but lots of wireless laptops.You want to increase the bandwidth available for the laptops by decreasing the bandwidth reserved for the Cisco 7920 phones.What is the lowest percentage of voice-allocated bandwidthyou can select on the WLAN controller？（）
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS？ （）
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode. When you set the link back to operational mode you loose association to the root bridge.Which action will correct the problem？（）
When configuring a WLAN controller for a voice application using Cisco 7920 wireless IP phones，which two general control settings should you select？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is， you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.What level do you set the bandwidth to？（）