A. It must be issued before the network command to enable the OSPF pr ocess for IPv6.
B. It must be issued after the network command to enable the OSPF process for IPv6.
C. It must be issued in router global configuration mode to enable the OSPF process for IPv6.
D. It must be issued in interface configuration mode to ena ble the OSPF process for IPv6.
您可能感興趣的試卷
你可能感興趣的試題
In IPv6, the interfaces running OSPF can be configured with multiple ad dress prefixes.
Which statement is true about the IPv6 addresses that can be included into the OSPF process?" （）
A. Specific addresses can be selected using a prefix list.
B. Specific addresses can be selected using a route map.
C. Specific addresses cann ot be selected for importation into the OSPF process.
D. Specific addresses can be selected using an ACL.
A. The shortest path first (SPF) algorithm is performed on the LSA database.
B. The OSPF adjacencies are cleared and initiated again.
C. The OSPF database is repopulated. Then the shortest path first (SPF) algorithm is performed.
D. The route table is cleared. Then the OSPF neighbors are reformed.
A. all routers in a local segment
B. all routers in an autonomous system
C. all hosts in a local segment
D. all hosts in a particular multicast group
A. If a packet is sent to a multicast group address, the multicast frame contains the source multicast address.
B. A router does not have to be a member of a multicast group to receive multicast data.
C. A router must be a member of a multicast group to send to the group.
D. A router does not have to be a member of a multicast group to send to the group.
E. If a packet is sent to a multicast group address, all members of the multicast group will rece ive it.
F. A router must be a member of a multicast group to receive multicast data.
Refer to the exhibit. What two statements are true?（）
A. This is the designated router (DR) on the FastEthernet 0/0 link.
B. The output was generated by the show ip interface c ommand.
C. The router was configured with the commands:r outer ospf 1 network 172.16.6.0 0.0.0.255 area 1
D. The IP address of the backup designated router (BDR) is FE80::205:5FFF:FED3:5808.
E. Interface FastEthernet 0/0 was configured with the ipv6 o spf 1 area 1 command.
F. OSPF version 2 has been enabled to support IPv6.
最新試題
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（）ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1
Router R1 sits at an Enterprise branch office, using the Internet for its only connectivity back to the rest of the EnterprisE.Which of the following is not a ben efit of using an IPsec tunnel for packets sent through the Internet, between R1 and the rest of the Enterprise?（）
Which of the following IPv6 tunneling mechanisms support IPv6 IGP routing protocols?（）
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output？（）B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18
Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 1tunnel source loopback 1tunnel destination 192.168.1.2tunnel mode ipv6ip isatapipv6 address 2000::/64 eui - 64
The following configura tion exists on a router on one end of an IPv6 tunnel. Which type of tunnel is created by this configuration?（）interface loopback 1ip address 1.1.1.1 255.255.255.255interface tunnel 2ipv6 address 2000::1::/64tunnel source loopback 1tunnel destina tion 2.2.2.2tunnel mode ipv6ipipv6 eigrp 1
Which of the following are true of both OSPFv2 and OSPFv3?（）
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）
Which of the following must match for two directly connected routers running OSPF to establish a neighbor adjacency?（）
Which of the following answers lists a multicast IPv6 address?（）