You need to configure a new Cisco router to be installed in the Company VOIP network.
Which three interface commands will configure the switch port to support a connected Cisco phone and to trust the CoS values received on the port if CDP discovers that a Cisco phone is attached? ()
A.switchport voice vlan vlan-id
B.mls qos trust device cisco-phone
C.switchport priority extend cos_value
D.mls qos trust cos
E.mls qos trust override cos
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit.
Which three statements are true about trust boundaries in the campus network?()
A.Classification and markingoccur using 802.1ab QoS bits before reaching the trust boundary.
B.A device is trusted if it correctly declassifies packets.
C.A device is trusted if it correctly classifies packets.
D.Network trust boundaries are automatically configured in IOS version 12.3 and later.
E.The outermost trusted devices represent the trust boundary.
F.For scalability, classification should be done as close to the edge as possible.
Refer to the exhibit.
Which two statements are true about the required switch configurations to support a voice VLAN?()
A.CDP must be disabled on the switch port to prevent interference between CDP messages and voice traffic.
B.Port security cannot be configured on a port that is configured for a voice vlan.
C.Static secure MAC addresses should be configured on voice vlan ports to prevent access by devices other than IP phones.
D.CDP must be enabled on the switch port to allow configuration information to be passed to the IP phone.
E.Portfast must be enabled on the switch port.
F.802.1x authentication cannot be configured on a port configured for a voice vlan.
You have been tasked with setting a trust boundary on the Company network.
What is the basic function of this trust boundary?()
A. Trust boundaries are points in the network where Layer 2 CoS markings are converted to Layer 3 DSCP or IP precedence markings.
B. Trust boundaries are a point in the network where QoS functionality begins and ends.
C. Trust boundaries determine whether certain types of traffic can pass.
D. Trust boundaries are a point in the network where decisions about CoS markings on incoming packets are made.
E. None of the other alternatives apply
Refer to the exhibit. On basis of the configuration that is provided,
where will the trust boundary be established in this network? ()
A.at the PC
B.at the access switch
C.at the IP phone
D.at the distribution switch
You need to determine where the trust boundaries will be in a new Company VOIP design.
Which two statements are true about these trust boundaries?()
A.Trust boundaries are configured in the core of the network to provide the most efficient forwarding based upon QoS markings,
B.Setting trust boundaries at the edge of the network allows intermediate hop devices to administer QoS policies without detailed packet identification.
C.Trust boundaries are used to determine which QoS mechanism will be applied to the traffic.
D.At the trust boundaries, the untrusted traffic will be marked with a new QoS value appropriate for the policy in place at the point where the traffic entered the campus network.
E.Trust boundaries define the firewall rules for QoS admission into a network.
最新試題
Which option correctly identifies the Cisco IOS switching methods in descending order from the fastest method to the slowest method?()
Which statement is correct about the use of the virtual interface on a WLC ?()
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ? ()
During routine maintenance, G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However, after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ? ()
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this?()
What must be the same to make multiple switches part of the same Multiple Spanning Tree (MST)?()
How are STP timers and state transitions affected when a topology change occurs in an STP environment?()
Which router redundancy protocol cannot be configured for interface tracking?()
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2?()
Which statement is correct about RSTP port roles?()